HTLPO_15 Datasheet, PDF (1/10 Pages) PETERMANN-TECHNIK – High Temperature Low Power Oscillator for Low Cost

PETERMANN-TECHNIK GmbH
Lechwiesenstr. 13 ∙ D-86899 ∙ Landsberg am Lech
Tel: [phone] ∙ Fax: [phone]
[e-mail] ∙ www.petermann-technik.com
HIGH TEMPERATURE LOW POWER OSCILLATOR
SERIES „HTLPO“
1.0—110.0 MHz
FEATURES
+ 100% pin-to-pin drop-in replacement to quartz and MEMS based XO
+ High Temperature Low Power Oscillator for Low Cost
+ Excellent long time reliability-outperforms quartz-based XO
+ Operating temperature from -40°C to 125°C /-55°C to 125°C optional
+ Supply voltage of 1.8V, 2.5V to 3.3VDC
+ Excellent total frequency stability as low as ±20 ppm
+ LVCMOS/LVTTL compatible output
+ Express samples within 1 day ex works PETERMANN-TECHNIK
+ Pb-free, RoHS and REACH compliant / MSL1@260°C
APPLICATIONS
+ All high temperature applications for –40/+125°C (non AEQ-Q100
automotive and avionics)
GENERAL DATA^[1,2]
PARAMETER AND CONDITIONS
FREQUENCY RANGE
Output Frequency Range
FREQUENCY STABILITY AND AGING
Frequency Stability
SYMBOL
f
F_stab
OPERATING TEMPERATURE RANGE
Operating Temperature Range
T_use
Storage Temperature Range
T_stor
SUPPLY VOLTAGE AND CURRENT CONSUMPTION
Supply Voltage
VDD
Current Consumption
OE Disable Current
Standby Current
IDD
I_OD
I_std
MIN.
1
-20
-25
-30
-50
-40
-40
-55
1.62
2.25
2.52
2.7
2.97
2.25
–
–
–
–
–
–
–
–
TYP.
–
–
–
–
–
–
–
–
1.8
2.5
2.8
3.0
3.3
–
3.8
3.6
3.4
–
–
2.6
1.4
0.6
MAX.
110
+20
+25
+30
+50
+105
+125
+125
1.98
2.75
3.08
3.3
3.63
3.63
4.5
4.2
4
4.1
3.8
8.5
5.5
3.5
UNIT CONDITION
MHz
PPM
PPM
PPM
PPM
Inclusive of initial tolerance at 25°C, 1st year aging at 25°C,
and variations over operating temperature, rated power
supply voltage and load (15 pF ± 10%).
°C
°C
°C Storage
V
V
V
V
V
V
mA No load condition, f = 20 MHz, VDD= 2.8V, 3.0V, or 3.3V
mA No load condition, f = 20 MHz, VDD = 2.5V
mA No load condition, f = 20 MHz, VDD = 1.8V
mA VDD = 2.5V to 3.3V, OE = Low, output in high Z state
mA VDD = 1.8V, OE = Low, output in high Z state
µA VDD = 2.8V to 3.3V, ST = Low, output is pulled down
µA VDD = 2.5V, ST = Low, output is pulled down
µA VDD = 1.8V, ST = Low, output is pulled down
Note: 1. All electrical specifications in the above table are specified with 15 pF output load at default drive strength and for all VDD(s) unless otherwise stated.
2.The typical value of any parameter in the Electrical Characteristic table is specified for the nominal value of the highest voltage option for that parameter and at 25 °C
temperature.
CRYSTALS ∙ OSCILLATORS ∙ CERAMIC RESONATORS ∙ CERAMIC FILTERS ∙ SAW COMPONENTS
PAGE 1 OF 10 I SPEC 01 I REV.00 I NOVEMBER 2014