PI3TB212 Datasheet, PDF (4/11 Pages) Pericom Semiconductor Corporation – 10.3Gbps Thunderbolt and DisplayPort Switch

PI3TB212
10.3125Gbps Thunderbolt and DisplayPort Switch
Maximum Ratings
(Above which useful life may be impaired. For user guidelines, not tested.) _{Note: Stresses greater than those listed under MAXIMUM}
RATINGS may cause permanent damage to the device. This
Storage Temperature .....................................................–65°C to +150°C
Supply Voltage to Ground Potential .................................–0.5V to +4.6V
I/O (Pin7 and 8) DC Input Voltage .................................... –0.5V to 1.5V
is a stress rating only and functional operation of the device
at these or any other conditions above those indicated in the
operational sections of this specification is not implied. Expo-
sure to absolute maximum rating conditions for extended
I/O (pin 1, 2, 4, and 5) ........................................................-0.5V to 4.0V periods may affect reliability.
I/O (pin 10 and 11)..............................................................-0.5V to 2.6V
I/O (pin 19 and 20) ............................................................. –0.5V to 4.0V
DC Output Current ........................................................................ 120mA
Power Dissipation ............................................................................ 0.5W
Control Logic DC Input Voltage .......................................... VDD + 0.5V
Electrical Characteristics
Recommended Operating Conditions
Symbol
Parameter
Conditions
Min Typ Max Units
VDD
3.3V Power Supply
3.0 3.3 3.6 V
I_DD
current consumption in normal op-
peration
Control pins = GND or VDD, LSTx = VDD
300 780
I_{DDQ (Sys-}
tem off)
I_{DD_detect}
P_DD
P_{DDQ (Sys-}
tem off)
P_{DD_Detect}
T_CASE
Current consumption when S0 = 0
Current consumption during detect
Total Power from V_DD 3.3V supply
Power consumption when S0 = 0
Power consumption during detect
Case operating temperature range
S0 = 0, TBC-2 and TBC-4 = GND or VDD,
LSTx = VDD, all I/Os are floating
S0 = VDD, 10G_EN = 0, DP_EN# = VDD,
LSTx = VDD, all I/Os are floating
Control pins = GND or VDD, LSTx = VDD
S0 = 0, TBC-2 and TBC-4 = GND or VDD,
LSTx = VDD
S0 = VDD, 10G_EN = 0, DP_EN# = VDD,
LSTx = VDD
100 300 uA
120 300
1 2.8 mW
330 1080 uW
400 1080 uW
0
105 C
DC Electrical Characteristics for Switching over Operating Range
Parameters Description
Test Conditions⁽¹⁾
Min Typ⁽¹⁾ Max
VIH
Input HIGH Voltage for S0, DP_EN#,
10G_EN, TBC-4, TBC-2, TBC-11
VDD = 3.3V
1.8
VIL
Input LOW Voltage for S0, DP_EN#,
10G_EN, TBC-4, TBC-2, TBC-11
VDD = 3.3V
0.8
VIK
Clamp Diode Voltage
VDD= Max., I_IN = –18mA
–0.7 –1.2
IIH
Input HIGH Current for S0, DP_
EN#, 10G_EN, TBC-4. TBC-2
VDD = Max., V_IN = V_DD
-1
1
IIL
Input LOW Current for S0, DP_EN#,
10G_EN, TBC-4, TBC-2
VDD = Max., V_IN = 0V
-1
1
leakage from TBC-16
VDD = 0V, 1.5V present on TBC-16
-60
+60
TB Rx_1 (p/n) is floating
IOFF _{(TBC pins)} ^{leakage from TBC-18}
VDD = 0V, 1.5V present on TBC-18
-20
+20
TB Rx_1 (p/n) is floating
VDD = 0V, 3.3V present on TBC
leakage from TBC-9, TBC-11, TBC- _pins
4, & TBC-2
-20
+20
ML1(p/n) is floating
All trademarks are property of their respective owners.
13-0026
4
V
µA
µA
03/12/13