PI74LPT16952 Datasheet, PDF (3/5 Pages) Pericom Semiconductor Corporation – Fast CMOS 3.3V 16-Bit Registered Transceivers

PI74LPT16952
12345678901234567890123456789012123456789012345678901234567890121234567890123³4^.5³6^V7890¹1⁶23^-4^B56^I7^T890^R12^E12^G345^I6^S78^T90^E12^R34^E56^D789^T01^R234^A56^N78^S90^C12^E12^I3^V456^E78^R90^S12
Maximum Ratings
(Above which the useful life may be impaired. For user guidelines, not tested.)
Storage Temperature ............................................................. –55°C to +125°C
Ambient Temperature with Power Applied ............................ –40°C to +85°C
Supply Voltage to Ground Potential (Inputs & Vcc Only) ...... –0.5V to +7.0V
Supply Voltage to Ground Potential (Outputs & D/O Only) .. –0.5V to +7.0V
DC Input Voltage .................................................................... –0.5V to +7.0V
DC Output Current .............................................................................. 120 mA
Power Dissipation .....................................................................................1.0W
Note:
Stresses greater than those listed under MAXIMUM
RATINGS may cause permanent damage to the de-
vice. This is a stress rating only and functional opera-
tion of the device at these or any other conditions
above those indicated in the operational sections of
this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods
may affect reliability.
DC Electrical Characteristics (Over the Operating Range, TA = –40°C to +85°C, VCC = 2.7V to 3.6V)
Parameters
Description
Test Conditions⁽¹⁾
Min. Typ⁽²⁾
VIH
Input HIGH Voltage (Input pins) Guaranteed Logic HIGH Level
2.2 —
Input HIGH Voltage (I/O pins)
2.0 —
VIL
Input LOW Voltage
Guaranteed Logic LOW Level
–0.5 —
(Input and I/O pins)
IIH
Input HIGH Current (Input pins) VCC = Max.
VIN = 5.5V
——
Input HIGH Current (I/O pins) VCC = Max.
VIN = VCC
——
IIL
Input LOW Current (Input pins) VCC = Max.
VIN = GND
——
Input LOW Current (I/O pins)
VCC = Max.
VIN = GND
——
IOZH
High Impedance Output Current VCC = Max.
VOUT = 5.5V
—
—
IOZL
(3-State Output pins)
VCC = Max.
VOUT = GND
—
—
VIK
Clamp Diode Voltage
VCC = Min., IIN = –18 mA
— –70
IODH
Output HIGH Current
VCC = 3.3V, VIN = VIH or VIL, VO = 1.5V⁽³⁾ –36 –60
IODL
Output LOW Current
VCC = 3.3V, VIN = VIH or VIL, VO = 1.5V⁽³⁾ 50
90
VOH
Output HIGH Voltage
VCC = Min.
IOH = –0.1 mA Vcc-0.2 —
VIN = VIH or VIL
IOH = –3 mA
2.4 3.0
VCC = 3.0V
IOH = –8 mA
2.4⁽⁵⁾ 3.0
VIN = VIH or VIL
IOH = –24 mA 2.0
—
VOL
Output LOW Voltage
VCC = Min.
IOL =0.1 mA
—
—
VIN = VIH or VIL
IOL = 16 mA
— 0.2
IOL = 24 mA
— 0.3
IOS
Short Circuit Current⁽⁴⁾
VCC = Max.⁽³⁾, VOUT = GND
–60 –85
IOFF
Power Down Disable
VCC = 0V, VIN or VOUT ≤ 4.5V
——
VH
Input Hysteresis
— 150
Max.
5.5
5.5
0.8
±1
±1
±1
±1
±1
±1
–1.2
–110
200
—
—
—
—
0.2
0.4
0.5
–240
±100
—
Units
V
V
V
µA
µA
µA
µA
µA
µA
V
mA
mA
V
V
V
V
V
V
V
mA
µA
mV
Notes:
1. For Max. or Min. conditions, use appropriate value specified under Electrical Characteristics for the
applicable device type.
2. Typical values are at Vcc = 3.3V, +25°C ambient and maximum loading.
3. Not more than one output should be shorted at one time. Duration of the test should not exceed one second.
4. This parameter is guaranteed but not tested.
5. VOH = VCC – 0.6V at rated current.
3
PS2076A 02/4/97