PI74FCT162Q245T Datasheet, PDF (3/6 Pages) Pericom Semiconductor Corporation – Fast, Low Noise CMOS 16-Bit Bidirectional Transceivers

PI74FCT162Q245T
123456789012345678901234567890121234567890123456789012345678^L90^O12^W1234^N56^O789^I0^S12^E34¹56⁶78^-9^B01^I2^T345^B67^I8^D90^I12^R12^E34^C56^T78^I9^O012^N34^A56^L789^T01^R234^A56^N78^S90^C12^E12^I3^V456^E78^R90^S12
Maximum Ratings
(Above which the useful life may be impaired. For user guidelines, not tested.)
Storage Temperature ................................................................. –65°C to +150°C
Ambient Temperature with Power Applied ................................. –40°C to +85°C
Supply Voltage to Ground Potential (Inputs & Vcc Only) .......... –0.5V to +7.0V
Supply Voltage to Ground Potential (Outputs & D/O Only) ....... –0.5V to +7.0V
DC Input Voltage ......................................................................... –0.5V to +7.0V
DC Output Current ................................................................................... 120 mA
Power Dissipation ......................................................................................... 1.0W
Note:
Stresses greater than those listed under
MAXIMUM RATINGS may cause permanent
damage to the device. This is a stress rating
only and functional operation of the device at
these or any other conditions above those
indicated in the operational sections of this
specification is not implied. Exposure to
absolute maximum rating conditions for
extended periods may affect reliability.
DC Electrical Characteristics (Over the Operating Range, TA = –40°C to +85°C, VCC = 5.0V ± 10%)
Parameters Description
Test Conditions⁽¹⁾
Min. Typ⁽²⁾
VIH
Input HIGH Voltage
Guaranteed Logic HIGH Level
2.0
VIL
Input LOW Voltage
Guaranteed Logic LOW Level
IIH
Input HIGH Current
Standard Input, VCC = Max.
VIN = VCC
IIH
Input HIGH Current
Bus Hold Input⁽⁴⁾, VCC = Max.
VIN = VCC
IIL
Input LOW Current
Standard Input, VCC = Min.
VIN = GND
IIL
Input LOW Current
Bus Hold Input⁽⁴⁾, VCC = Min.
VIN = GND
IBHH
Bus Hold
Bus Hold Input⁽⁴⁾, VCC = Min.
VIN = 2.0V
–50
IBHL
Sustain Current
VIN = 0.8V
+50
IOZH
High Impedance
VCC = Max.
VOUT = VCC
IOZL
Output Current
VCC = Max.
VOUT = GND
VIK
Clamp Diode Voltage
VCC = Min., IIN = –18 mA
–0.7
IO
Output Drive Current
VCC = Max.⁽³⁾, VOUT = 2.5V
–50
VH
Input Hysteresis
100
Max.
0.8
1
±100
–1
±100
1
–1
–1.2
–180
Units
V
V
µA
µA
µA
µA
µA
µA
µA
V
mA
mV
Notes:
1. For Max. or Min. conditions, use appropriate value specified under Electrical Characteristics for the applicable device type.
2. Typical values are at VCC = 5.0V, +25°C ambient and maximum loading.
3. Not more than one output should be shorted at one time. Duration of the test should not exceed one second.
4. Pins with Bus Hold are identified in the pin description.
5. This specification does not apply to bi-directional functionalities with Bus Hold.
292
PS2050A 04/12/96