PI5A3166 Datasheet, PDF (3/9 Pages) Pericom Semiconductor Corporation – Low Voltage SPST 0.8(ohm) Analog Switch

PI5A3166
Low Voltage SPST 0.8Ω Analog Switch
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
DC Electrical Characteristics
(T_A = –40°C to 85°C, unless otherwise noted.)
Parameter
Description
Test Conditions
Supply Voltage Min Typ Max Units
V_IAR
Analog Input Signal Range
-
I_A = 100mA, V_B = 0V
V_CC
0
- VCC V
- 0.7 1.1
I_A = 100mA, V_B= 2.4V
4.5V
- 0.6 1.0
I_A = 100mA, V_B = 4.5V
- 0.8 1.2
R_ON
(1)
ON Resistance
I_A = 100mA, V_B = 0V
I_A = 100mA, V_B = 3.0V
I_A = 100mA, V_B = 0V
I_A = 100mA, V_B = 2.3V
3.0V
2.3V
- 0.8 1.3
- 0.9 1.9 
- 1.0 1.5
- 1.2 1.8
I_A = 100mA, V_B = 0V
I_A = 100mA, V_B = 1.65V
1.65V
- 1.3 1.9
- 2.0 2.8
I_A = 100mA, V_B = 0V,2.4V,4.5V
4.5V
- 0.2 0.4
R_ONF
(2)
ON Resistance Flatness
I_A = 100mA, V_B = 0V,1.5V,3.3V
I_A = 100mA, V_B = 0V,1.1V,2.5V
3.3V
2.5V
- 0.2 0.4
-
0.4 0.6

I_A = 100mA, V_B = 0V, 0.7V, 1.8V
1.8V
- 1.0 1.4
V_IH
Input High Voltage
V_IL
I_{OFF (B)}
I_{NC(A, B)}
Input Low Voltage
Source Off Leakage
Current
Channel On Leakage
Current
Logic High Level
Logic Low Level
V_CC=5.5V, VA =1V, 4.5V
VB =1V, 4.5V
-
V_CC = 1.65V
1
-
-
V_CC = 2.3V
1.2
-
-
V_CC = 3V
1.3 -
-
V
V_CC = 4.2V
1.5
-
-
V_CC = 5.5V
1.8
-
-
V_CC = 1.65V
-
- 0.4
V_CC = 2.3V
-
- 0.6
V_CC = 3V
-
- 0.8 V
V_CC = 4.2V
-
-
1
V_CC = 5.5V
-
- 1.2
V_CC = 3V
-20 - +20
V_CC = 1.65 to
5.5V
-40
-
nA
+40
I_PWROFF
I_CC
Input Leakage Current for
Power off
Quiescent Supply Current
0≤V_A≤5.5V
0≤V_B≤5.5V
All channels ON or OFF,
V_B = V_CC or GND, I_OUT=0
V_CC =0V
V_CC = 3.6V
V_CC = 5.5V
-5 -
5 µA
- 0.002 0.1
- 0.002 0.1
µA
Notes:
1. Measured by voltage drop between A and B pins at the indicated current through the device. ON resistance is determined by the lower
of the voltages on two ports (A or B).
2. Flatness is defined as difference between maximum and minimum value of ON resistance over the specified range of conditions.
Guaranteed by design.
Capacitance⁽¹⁾
Symbol
Parameter
C_IN
C_IO-B
Control Input
For B Port, Switch OFF
C_IOA-ON
For A Port, Switch ON
Test Conditions
V_CC = 5.0V, f =1 MHz, T_A=25°C
Notes:
1. Capacitance is characterized but not tested in production
Min.
-
-
-
Typ.
3.5
15.0
34.0
Max.
-
-
-
Units
pF
2015-09-0003
PT0444-1
09/23/15
3