PI4ULS5V202 Datasheet, PDF (3/11 Pages) Pericom Semiconductor Corporation – 2-Bit Bi-directional Level Shifter with Automatic Sensing & Ultra Tiny Package

PI4ULS5V202
2-Bit Bi-directional Level Shifter with
Automatic Sensing & Ultra Tiny Package
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
DC Electrical Characteristics
Unless otherwise specified, -40°C≤T_A≤85°C, 1.2V≤Vcc≤5.5V
Symbol
Parameter
Test Conditions
Min Typ Max Unit
V_IHB B port Input HIGH Voltage
-
V_CCB –
0.2
-
-
V
V_ILB B port Input LOW Voltage
-
V_IHA A port Input HIGH Voltage
-
-
-
V_CCA –
0.2
-
0.15
V
-
V
V_ILA A port Input LOW Voltage
-
V_IH Control Pin Input HIGH Voltage -
-
-
V_CCA –
0.2
-
0.15
V
-
V
V_IL
V_OHB
Control Pin Input LOW Voltage
B port Output HIGH Voltage
V_OLB B port Output LOW Voltage
V_OHA A port Output HIGH Voltage
V_OLA A port Output LOW Voltage
I_QVCB V_CCB Supply Current
I_QVCA V_CCA Supply Current
I_TS−V_CCB B Tri−state Output Mode
-
B port source current = -20 µA
B port sink current =1 mA
A port source current= -20 µA
A port sink current =1 mA
B port and A port unconnected, VEN
= V_CCA
B port and A port unconnected, VEN
= V_CCA
B port and A port unconnected, VEN
= GND
-
-
0.15
V
2/3 *
V_CCB
-
-
V
-
-
1/3 *
V_CCB
V
2/3 *
V_CCA
-
-
V
-
-
1/3 *
V_CCA
V
-
0.5
5.0
µA
-
0.3
5.0
µA
-
0.1
1
µA
I_TS−V_CCA
A Tri−state Output Mode Supply
Current
B port and A port unconnected, VEN
= GND
-
0.1
1
µA
I/O Tri−state Output Mode
I_OZ
Leakage
Current
-
0.1
1.0
µA
R_PU Pull−Up Resistors I/O A and B
-
10
-
kΩ
Note: All units are production tested at T_A = +25°C. Limits over the operating temperature range are guaranteed by design.
Typical values are for V_CCB = +2.8 V, V_CCA = +1.8 V and T_A = +25°C.
AC Electrical characteristics
Timing Characteristics − Rail−to−Rail Driving Configuration
(I/O test circuits of Figures 2, 3 and 7, C_LOAD = 15 pF, driver output impedance ≤ 50Ω, R_LOAD = 1 MΩ, unless otherwise specified)
Symbol
Parameter
Test Conditions
Min Typ Max Unit
V_CCA= 1.8V , V_CCB = 2.8V
t_RB
t_FB
t_RA
B port Rise Time
B port Fall Time
A port Rise Time
-
-
- ₁₅
nS
-
-
- ₁₅
nS
-
-
- ₂₅
nS
t_FA
t_{PHL−A−B}
t_{PLH−A−B}
t_{PHL−B−A}
t_{PLH−B−A}
t_PPSKEW
MDR
A port Fall Time
Propagation Delay
(Driving A)
Propagation Delay
(Driving B)
Part−to−Part Skew
Maximum Data Rate
-
-
- ₁₀
nS
-
-
- ₁₅
nS
-
-
- ₁₅
nS
-
-
- ₁₅
nS
-
-
- ₁₅
nS
-
-
-
5
nS
-
20 -
-
Mbps
To be continued.
2015-07-0023
PT0461-3 07/28/15
3