PI3B4010 Datasheet, PDF (3/6 Pages) Pericom Semiconductor Corporation – 3.3V, High-Bandwidth, 40:10-Bit DDR Mux/Demux NanoSwitch

PI3B4010
3.3V, High Bandwidth, 40:10-Bit,
DDR Mux/Demux NanoSwitch _{1122334455667788990011223344556677889900112233445566778899001122112233445566778899001122334455667788990011223344556677889900112211223344556677889900112233445566778899001122334455667788990011221122334455667788990011223344556677889900112233445566778899001122112233445566778899001122}
DC Electrical Characteristics over Operating Range (T_A = 0°C to 70°C, V_CC = 3.3V ±5%)
Parameter
Description
Test Conditions⁽¹⁾
Min. Typ.⁽²⁾
Max.
V_IH
Input HIGH Voltage
Guaranteed HIGH Level
1.6
– V_CC +0.3
V_IL
Input LOW Voltage
Guaranteed HIGH Level
–0.3
–
0.9
V_IK
Clamp Diode Voltage
V_CC = Max., V_{IN =} –18mA
–
–0.7
–1.2
I_IH
Input HIGH Current
V_CC = Max., V_IN = V_CC
–
–
±10
I_IL
Input LOW Current
V_CC = Max., V_IN = GND
–
–
±10
R_ON
Switch On Resistance⁽³⁾ V_CC = Min., 0.8V ≤V_IN ≤2.5V, I_IN = –20mA
–
25
35
R_FLAT(ON) On Resistance Flatness⁽⁴⁾ V_CC = Min., V_IN@0.8V and 1.7V I_IN = –20mA
–
1.0
–
On Resistance match
∆R_ON from center ports to any V_CC = Min., 0.8V ≤V_IN ≤2.5V, I_IN = –20mA
–
0.9
2
other port⁽⁴⁾
R_PD
Pull-Down Resistance
V_IN = 0V to 2.5V
80
100
130
Units
V
µA
Ω
Capacitance (T_A = 25°C, f = 1 MHz)
Parameters
Description
Test Conditions
Typ.⁽⁴⁾
Max.
Units
C_IN
Input Capacitance
3.5
–
C_OFF(A)
C_ON(A/B)
Port A Capacitance, Switch OFF
A/B Capacitance, Switch ON
V_IN = 0V
12.0
–
pF
15.0
–
C_OFF(B)
Port B Capacitance, Switch OFF
4.5
–
Notes:
1. For min. or max. conditions, use appropriate value specified under Electrical Characteristics for the applicable device type.
2. Typical values are at V_CC = 3.3V, T_A = 25°C ambient and maximum loading.
3. Measured by the voltage drop between A and B pins at indicated current through the switch. ON resistance is determined by the
lower of the voltages on the two (A & B) pins.
4. This parameter is determined by device characterization but is not production tested.
Power Supply Characteristics
Parameters
Description
Test Conditions⁽¹⁾
Min. Typ.⁽²⁾
I_CC
Quiscent Power Supply Current
V_CC = Max., V_IN = GND or V_CC –
–
Notes:
1. For Max. or Min. conditions, use appropriate value specified under Electrical Characteristics for the applicable device.
2. Typical values are at V_CC = 3.3V, +25°C ambient.
3. Per TTL driven input (control inputs only); A and B pins do not contribute to I_CC.
Max.
10
Units
µA
3
PS8571A
12/11/02