PI3A412 Datasheet, PDF (3/11 Pages) Pericom Semiconductor Corporation – 0.4ohm, 3.3V, Quad SPDT Analog Switch

COMPANY CONFIDENTIAL
PI3A412
0.4Ω, 3.3V, Quad SPDT Analog Switch
Electrical Specifications - Single +3.3V Supply
(V_CC = +3.3V ± 10%, GND = 0V, V_IH = 1.3V, V_IL = 0.5V) (T_A = –40°C to +85°C)
Parameter
Symbol
Conditions
Min.⁽¹⁾
Analog Signal Range ⁽³⁾ V_ANALOG
0
Typ. ⁽²⁾
Max. ⁽¹⁾ Units
V_CC
V
On Resistance
On-Resistance Match
Between Channels⁽⁴⁾
R_ON
∆R_ON
V_CC = 2.7V, I_COM = 100mA,
V_IN = +1.5V
0.4
0.6
0.08
0.09
Ω
On-Resistance Flatness⁽⁵⁾ R_FLAT(ON)
V_CC = 2.7V, I_COMx = 100mA,
V_IN = 0.8V, 2.0V
0.1
0.15
Off Leakage Current⁽⁶⁾
I_NC (off)
or
I_NO (off)
V_CC = 3.6V
V_NO or V_NC = 0.3V, 3.3V
-400
On Leakage Current⁽⁶⁾
I_{COMx (on)}
V_CC = 3.6V,
V_COMx= 0.3V, 3.3V
-400
400
nA
400
Notes:
1. The algebraic convention, where most negative value is a minimum and most positive is a maximum, is used in this data sheet.
2. Typical values are T_A = 25°C, V_CC = 4.2V unless otherwise specified.
3. Guaranteed by design.
4. ∆R_ON = R_ON match between channels
5. Flatness is defined as the difference between the maximum and minimum value of On-Resistance measured.
6. Leakage parameters are 100% tested at maximum rated hot temperature and guaranteed by correlation at +25ºC.
Electrical Specifications - Single +4.2V Supply
(V_CC = +4.2V ± 10%, GND = 0V, V_IH = 1.6V, V_IL = 0.7V) (T_A = –40°C to +85°C)
Parameter
Symbol
Conditions
Min.⁽¹⁾
Analog Signal Range ⁽³⁾ V_ANALOG
0
On Resistance
On-Resistance Match
Between Channels⁽⁴⁾
R_ON
∆R_ON
V_CC = 4.0V, I_COMx = 100mA,
V_IN = +1.5V
On-Resistance Flatness⁽⁵⁾ R_FLAT(ON)
V_CC = 4.0V, I_COMx = 100mA,
V_IN = 0.8V, 2.0V
Off Leakage Current⁽⁶⁾
I_NC (off)
or
I_NO (off)
V_CC = 4.4V,
V_NO or V_NC = 0.3V, 3.3V
-400
On Leakage Current⁽⁶⁾
I_COMx (on)
V_CC = 4.4V,
V_COMx = 0.3V, 3.3V
-400
Typ. ⁽²⁾
0.4
0.08
0.1
Max. ⁽¹⁾ Units
V_CC
V
0.6
0.09
Ω
0.15
400
nA
400
Notes:
1. The algebraic convention, where most negative value is a minimum and most positive is a maximum, is used in this data sheet.
2. Typical values are T_A = 25°C, V_CC = 4.2V unless otherwise specified.
3. Guaranteed by design.
4. ∆R_ON = R_ON match between channels
5. Flatness is defined as the difference between the maximum and minimum value of On-Resistance measured.
6. Leakage parameters are 100% tested at maximum rated hot temperature and guaranteed by correlation at +25ºC.
06-0068
PS8834
05/22/06
3