English
Language : 

PT7M6101 Datasheet, PDF (2/5 Pages) Pericom Semiconductor Corporation – Ultra Low Voltage Detectors
◁
PT7M6101/6102
Ultra Low Voltage Detectors
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||| ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||| |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Maximum Ratings
Storage Temperature………………………………………… - 65oC to +150oC
Ambient Temperature with Power Applied....................-40oC to +85oC
Supply Voltage to Ground Potential (VCC to GND)………... - 0.3 to VCC +6.0V
DC Input/Output Current …………………………………………………20mA
Power Dissipation……………………………………………………….245mW
Note:
Stresses greater than those listed under MAXIMUM
RATINGS may cause permanent damage to the
device. This is a stress rating only and functional
operation of the device at these or any other condi-
tions above those indicated in the operational sec-
tions of this specification is not implied. Exposure
to absolute maximum rating conditions for extended
periods may affect reliability.
AC Electrical Characteristics
(VCC = +0.9V to +5.5V, unless otherwise noted. Typical values are at TA = +25ºC)
Description
Sym
Test Conditions
Vcc or RESET-IN to Reset Delay
IN rising, step signal from 0V to 1V
Propagation Delay(D0 only)
tP IN falling, step signal from 1V to 0V
Min Typ Max Unit
-
60
-
µs
-
40
-
µs
DC Electrical Characteristics
(VCC = +0.9V to +5.5V, unless otherwise noted. Typical values are at TA = +25ºC)
Description
Sym
Test Conditions
Min
Typ Max Unit
Operating Voltage Range
VCC TA= -40ºC ~+85ºC
0.9
-
5.5
V
VCC=1.2V, no load , reset not asserted
-
7.5
13
Supply Current
ICC VCC=1.8V, no load , reset not asserted
-
9
16
µA
VCC=3.6V, no load , reset not asserted
-
16
25
IN Threshold
VRSTIN
1.3V<=VCC<=5.5V, -40ºC ~+85ºC (PT7M6101)
1.3V<=VCC<=5.5V, -40ºC ~+85ºC (PT7M6102)
90
190
100
200
110
mV
210
VCC>=1.1V, Isource=50µA, reset not asserted
0.8×Vcc -
-
Push-pull OVRI
Output High Voltage
VOH
VCC>=1.5V, Isource=150µA, reset not asserted
VCC >=1.0V, Isource=50µA, reset asserted
0.8×Vcc -
0.8×Vcc -
-
-
-
VCC >=1.5V, Isource=150µA, reset asserted
0.8×Vcc -
-
Push-pull OVRI
Output Low Voltage
Push-pull OVRI
Output Low Voltage
VCC >=1.0V, Isink=80µA, reset asserted
VCC >=1.5V, Isink=200µA, reset asserted
VOL
VCC >=1.1V, Isink=80µA, reset not asserted
VCC >=1.5V, Isink=200µA, reset not asserted
-
- 0.2×Vcc
-
- 0.2×Vcc
V
-
- 0.2×Vcc
-
- 0.2×Vcc
Open-Drain OVRI
Output Low Voltage
VCC >=1.0V, Isink=80µA, reset asserted
VCC >=1.5V, Isink=200µA, reset asserted
-
-
0.15
V
-
-
0.2
Open-Drain OVRI
Output Leakage Current
IN Leakage Current
Reset Threshold Hysteresis
ILKG
IRSTIN
VHYS
VCC > VTH , reset not asserted
-
-
-
-
1.0 µA
-25
-
+25 nA
-
10
-
mV
2013-11-0004
PT0260-5
12/12/13
2
 ▷