PI5V331 Datasheet, PDF (2/5 Pages) Pericom Semiconductor Corporation – Low ON Resistance Wideband/Video Dual 4-Channel Mux/Demux

PI5V331
Low ON Resistance Wideband Video
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345^D67^u89^a01^l2⁴34^-5^C67^h89^a01ⁿ2ⁿ34^e5^l67^M890^u12^x1^/2^D34^e56^m78^u90^x12
Maximum Ratings
(Above which the useful life may be impaired. For user guidelines, not tested.)
Storage Temperature ........................................................... –65°C to +150°C ^Note:
Stresses greater than those listed under MAXIMUM
Ambient Temperature with Power Applied .......................... –40°C to +85°C _{RATINGS may cause permanent damage to the de-}
Supply Voltage to Ground Potential (Inputs & Vcc Only) ... –0.5V to +7.0V vice. This is a stress rating only and functional opera-
Supply Voltage to Ground Potential (Outputs & D/O Only) –0.5V to +7.0V ^{tion of the device at these or any other conditions}
above those indicated in the operational sections of
DC Input Voltage .................................................................. –0.5V to +7.0V _{this specification is not implied. Exposure to absolute}
DC Output Current ............................................................................ 120 mA maximum rating conditions for extended periods may
Power Dissipation ................................................................................... 0.5W ^{affect reliability.}
DC Electrical Characteristics (Over the Operating Range, TA = –40°C to +85°C, VCC = 5V ±5%)
Parameters Description
Test Conditions⁽¹⁾
Min. Typ⁽²⁾
VANALOG Analog Signal Range
0
—
VIH
Input HIGH Voltage
Guaranteed Logic HIGH Level
2.0 —
VIL
Input LOW Voltage
Guaranteed Logic LOW Level
–0.5 —
IIH
Input HIGH Current
VCC = Max., VIN = VCC
——
IIL
Input LOW Current
VCC = Max., VIN = GND
——
IO
Analog Output Leakage Current 0 ≤S1, S2 or D ≤VCC, Switch Off
——
VIK
Clamp Diode Voltage
VCC = Min., IIN = –18 mA
— –0.7
IOS
Short Circuit Current⁽³⁾
S1, S2, D = 0V VCC
100 —
VH
Input Hysteresis at Control Pins
— 150
RON
Switch On Resistance⁽⁴⁾
VCC = Min., VOUT = 0.975V
RL = 75Ω, ION = 13 mA
—
3
VCC = MIN., VOUT = 1.95V
RL = 75Ω, ION = 26 mA
—
7
Max.
2.0
—
0.8
±1
±1
±1
–1.2
—
—
7
10
Units
V
V
V
µA
µA
µA
V
mA
mV
Ω
Ω
Notes:
1. For Max. or Min. conditions, use appropriate value specified under Electrical Characteristics for the applicable device type.
2. Typical values are at Vcc = 5.0V, TA = 25°C ambient and maximum loading.
3. Not more than one output should be shorted at one time. Duration of the test should not exceed one second.
4. Measured by the voltage drop between S1, S2, and D I/O pins at indicated current through the switch. ON resistance is deter-
mined by the lower of the voltages on the S1, S2, and D I/O pins. VOUT is the voltage across RL.
2
PS8117 08/07/97