PI5C6801C Datasheet, PDF (2/5 Pages) Pericom Semiconductor Corporation – 10-Bit Bus Switch with Precharged Outputs for Live Insertion and - 2V Undershoot Protection

PI5C6801C
10-Bit BusSwitch with PrechargedOutputs
11223344556677889900112233445566778899001122334455667788990011221122334455667788990011223344556677889900112233445566778899001122112233445566778899001122^f33^o4455^r66^L7788ⁱ99^v0011^e2233^I44ⁿ5566^s77^e88^r9900^t11^io2211ⁿ2233^a4455ⁿ6677^d8899^-00²11^V223344^U5566ⁿ7788^d9900^e11^r22^s3344^h55^o6677^o88^t9900^P1122^r11^o2233^t44^e55^c66^t77ⁱ88^o9900ⁿ1122
Absolute Maximum Ratings Over Free-Air Temperature Range*
(Above which the useful life may be impaired. For user guidelines, not tested.)
Storage Temperature ............................................................ –65°Cto+150°C
Supply Voltage Range ................................................................ –0.5Vto+7V
Note:
Stresses greater than those listed under MAXIMUM
RATINGS may cause permanent damage to the de-
DC Input Voltage⁽¹⁾ .................................................................................... –0.5V to +7V
Input Clamp Current, I_IK (V₁<0) .......................................................... –50mA
DC Output Current .............................................................................. 120mA
vice. This is a stress rating only and functional
operation of the device at these or any other condi-
tions above those indicated in the operational sec-
tions of this specification is not implied. Exposure to
Power Dissipation⁽²⁾ .................................................................................................. 0.5W
absolute maximum rating conditions for extended
periods may affect reliability.
Notes:
1. The input and output negative-voltage ratings may be exceeded if the input and output clamp-current ratings are observed.
2. The maximum package power dissipation is calculated using a junction temperature of 150°C and a board trace length of 750 mils.
Recommended Operating Conditions
Parameter
Description
Min.
Max.
Units
V_CC
BIASV
V_IH
Supply voltage
Supply voltage
High-Level input voltage
4
5.5
1.3
V_CC
V
2
V_IL
Low-level input voltage
0.8
T_A
Operating free-air temperature
–40
85
°C
Electrical Characteristics (Over Recommended Operating Free-air Temperature Range)
Parameter
Test Conditions
Min. Typ⁼ Max.
V_IK
V_CC = 4.5V
I_I = –18mA
–1.8
I_I
V_CC = 5.5V
V_I = 5.5V or GND
±5
I_O
V_CC = 4.5V
BIASV = 2.4V V_O= 0V
–0.20
I_CC
V_CC = 5.5V
I_O = 0A
V_I = V_CC or GND
100
∆I_CC^E Control pins V_CC = 5.5V
One input at 3.4V Other at V_CC or GND
2.5
C_I
Control pins V_I = 3V or 0V
3.5
C_O(OFF)
V_O = 3V or 0V Switch Off
4.5
R_ON*
V_CC = 4V
V_I = 2.4V
V_I = 0V
I_I = 15mA
I_I = 64mA
9
28
5.5
8
V_CC = 4.5V
V_I = 0V
I_I = 30mA
5
8
V_I = 2.4V
I_I = 15mA
9
16
Notes:
* Measured by the voltage drop between the A and B terminals at the indicated current through the switch.
On-state resistance is determined by the lower of the voltages of the two (A or B) terminals.
E This is the increase in supply current for each input that is at the specified TTL voltage level rather the V_CC or GND.
= All typical values are at V_CC = 5V, T_A = 25°C.
Units
V
µA
mA
µA
mA
pF
Ω
2
PS8374B
05/02/00