PI3VT3306 Datasheet, PDF (2/4 Pages) Pericom Semiconductor Corporation – 2-Bit, 2-Port, Low Voltage Translator Bus Switch

PI3VT3306
2-Bit, 2-Port, Low Voltage
Translator Bus Switch _{1122334455667788990011223344556677889900112233445566778899001122112233445566778899001122334455667788990011223344556677889900112211223344556677889900112233445566778899001122334455667788990011221122334455667788990011223344556677889900112233445566778899001122112233445566778899001122}
Maximum Ratings
(Above which the useful life may be impaired. For user guidelines, not tested.)
Storage Temperature ........................................................ –65°C to +150°C
Ambient Temperature with Power Applied ......................... –40°C to +85°C
Supply Voltage to Ground Potential ......................................... –0.5Vto+4.6V
DC Input Voltage .................................................................. –0.5Vto+5.5V
DC Output Current ............................................................................ 120mA
Power Dissipation ................................................................................ 0.5W
Note:
Stresses greater than those listed under MAXIMUM
RATINGS may cause permanent damage to the device.
This is a stress rating only and functional operation of
the device at these or any other conditions above those
indicated in the operational sections of this specifica-
tion is not implied. Exposure to absolute maximum
rating conditions for extended periods may affect reli-
ability.
DC Electrical Characteristics (Over Operating Range, T_A = –40°C to +85°C, V_CC = 3.3V ±10%)
Parameters
Description
Test Conditions⁽¹⁾
Min. Typ.⁽²⁾
Max. Units
V_IH
Input HIGH Voltage
V_IL
Input LOW Voltage
Guaranteed Logic HIGH Level
1.8
Guaranteed Logic LOW Level
–0.5
V_CC +0.3V
V
0.8
I_IH
Input HIGH Current
V_CC = Max., V_IN = V_CC
±1
I_IL
Input LOW Current
V_CC = Max., V_IN = GND
±1
µA
I_OZH High Impedance Output Current 0 ≤ A, B ≤ V_CC
±1
V_CC = Min., V_IN = 0.0V, I_ON = 8mA
5
8
R_ON Switch On Resistance
V_CC = Min., V_IN = 1.7V, I_ON = 8mA
V_CC = 2.3V, V_IN = 0.0V, I_ON = 8mA
10
22
Ω
6
9
V_CC = 2.3V, V_IN = 1.3V, I_ON = 8mA
25
30
V_P
Pass Voltage
V_IN = V_CC = 3.3V, I_OUT = –5µA
V_IN = V_CC = 2.5V, I_OUT = –5µA
2.3
2.5
1.8
2.9
V
Capacitance (T_A = 25°C, f = 1 MHz)
Parameters⁽⁵⁾
Description
Test Conditions
Typ.
Units
C_IN
C_OFF
Input Capacitance
A/B Capacitance, Switch Off
V_IN = 0V
3.5
5.0
pF
C_ON
A/B Capacitance, Switch On
10.0
Notes:
1. For Max. or Min. conditions, use appropriate value specified under Electrical Characteristics for the applicable device type.
2. Typical values are at V_CC = 3.3V, T_A = 25°C ambient and maximum loading.
3. Not more than one output should be shorted at one time. Duration of the test should not exceed one second.
4. Measured by the voltage drop between A and B pin at indicated current through the switch. ON resistance is determined
by the lower of the voltages on the two (A,B) pins.
5. This parameter is determined by device characterization but is not production tested.
2
PS8533 03/22/01