PI3C3861 Datasheet, PDF (2/5 Pages) Pericom Semiconductor Corporation – 2.5V/3.3V, High Bandwidth, Hot Insertion, 10-Bit, 2-Port, BusSwitch

PI3C3861
2.5V/3.3V, High-Bandwidth,
112233445566778899001122334455667788990011223344556677889900112211223344556677889900112233445566778899001122334455667788990011221122334455667788990011223344556677889900112233^H4455^o6677^t88^-99^I00ⁿ1122^s11^e22^r3344^t55^io6677ⁿ8899^,00¹1122⁰33^-4455^B6677^it8899^, 00²11^-22^P3344^o5566^r77^t88^,99^B0011^u2211^s2233^S4455^w6677ⁱ88^t99^c00^h1122
Maximum Ratings
(Above which the useful life may be impaired. For user guidelines, not tested.)
Storage Temperature .......................................................... –65°C to +150°C
Ambient Temperature with Power Applied ............................. –40°Cto+85°C
Note:
Stresses greater than those listed under MAXIMUM
RATINGS may cause permanent damage to the device.
Supply Voltage to Ground Potential (Inputs & Vcc Only) ........ –0.5Vto+4.6V This is a stress rating only and functional operation
Supply Voltage to Ground Potential (Outputs & D/O Only) ..... –0.5Vto+4.6V
DC Input Voltage .................................................................... –0.5Vto+5.5V
of the device at these or any other conditions above
those indicated in the operational sections of this
specification is not implied. Exposure to absolute maxi-
DC Output Current ..............................................................................120mA mum rating conditions for extended periods may affect
Power Dissipation .................................................................................. 0.5W ^reliability.
DC Electrical Characteristics (Over Operating Range, T_A = –40°C to +85°C, V_CC = 3.3V ±10%)
Parameters Description
Test Conditions⁽¹⁾
Min. Typ⁽²⁾
VIH
Input HIGH Voltage
Guaranteed Logic HIGH Level
2.0
VIL
Input LOW Voltage
Guaranteed Logic LOW Level
–0.5
IIH
Input HIGH Current
VCC = Max., VIN = VCC
IIL
Input LOW Current
VCC = Max., VIN = GND
IOZH
High Impedance Output Current 0 ≤ A, B ≤ VCC
VIK
Clamp Diode Voltage
VCC = Min., IIN = –18mA
–0.73
RON
Switch On Resistance⁽⁴⁾
VCC = Min., VIN = 0.0V, ION = 48mA
5
VCC = Min., VIN = 2.4V, ION = 15mA
8
Max.
0.8
±1
±1
±1
– 1.2
7
15
Units
V
µA
V
Ω
Capacitance (T_A = 25°C, f = 1 MHz)
Parameters⁽⁵⁾
Description
CIN
Input Capacitance
COFF
A/B Capacitance, Switch Off
CON
A/B Capacitance, Switch On
Test Conditions
VIN = 0V
VIN = 0V
VIN = 0V
Typ Units
3.5
5.0
pF
10.0
Notes:
1. For Max. or Min. conditions, use appropriate value specified under Electrical Characteristics for the applicable device type.
2. Typical values are at V_CC = 3.3V, T_A = 25°C ambient and maximum loading.
3. Not more than one output should be shorted at one time. Duration of the test should not exceed one second.
4. Measured by the voltage drop between A and B pin at indicated current through the switch. ON resistance is determined
by the lower of the voltages on the two (A,B) pins.
5. This parameter is determined by device characterization but is not production tested.
2
PS8198C
02/11/03