PI3C3384 Datasheet, PDF (2/4 Pages) Pericom Semiconductor Corporation – 2.5V/3.3V, High Bandwidth, Hot Insertion 10-Bit, 2-Port, Bus Switch

PI3C3384/PI3C32384 (25Ω)
2.5V/3.3V, High Bandwidth,
1122334455667788990011223344556677889900112233445566778899001122112233445566778899001122334455667788990011223344556677889900112211223344556677889900112233445566778899001122334455^H667788^o99^t0011^I22ⁿ1122^s33^e44^r55^t66ⁱ77^o8899ⁿ0011^,22¹33⁰4455^-66^B7788ⁱ99^t00^,11²2233^-44^P5566^o77^r88^t9900^B1122^u1122^s33^S4455^w6677ⁱ88^t99^c00^h1122
Maximum Ratings
(Above which the useful life may be impaired. For user guidelines, not tested.)
Storage Temperature ........................................................... –65°C to +150°C
Ambient Temperature with Power Applied .......................... –40°C to +85°C
Supply Voltage to Ground Potential (Inputs & V_CC Only) ... –0.5V to +4.6V
Supply Voltage to Ground Potential (Outputs & D/O Only) –0.5V to +4.6V
DC Input Voltage ................................................................... –0.5V to +5.5V
DC Output Current .............................................................................. 120 mA
Power Dissipation .................................................................................... 0.5W
Note:
Stresses greater than those listed under
MAXIMUM RATINGS may cause permanent dam-
age to the device. This is a stress rating only and
functional operation of the device at these or any
other conditions above those indicated in the opera-
tional sections of this specification is not implied.
Exposure to absolute maximum rating conditions
for extended periods may affect reliability.
DC Electrical Characteristics (Over Operating Range, T_A = –40°C to +85°C, V_CC = 3.3V ± 10%)
Parameters
Description
Test Conditions⁽¹⁾
Min. Typ.⁽²⁾ Max.
V_IH Input HIGH Voltage
Guaranteed Logic HIGH Level
2.0 — —
V_IL
Input LOW Voltage
Guaranteed Logic LOW Level
–0.5 — 0.8
I_IH
Input HIGH Current
V_CC = Max., VIN = V_CC
—
—
±1
I_IL
Input LOW Current
V_CC = Max., VIN ₌ GND
—
—
±1
I_OZH High-Impedence Output Current 0 ≤ A, B ≤ V_CC
—
—
±1
V_IK Clamp diode Voltage
R_ON Switch On Resistance⁽⁴⁾
V_CC = Min., I_IN = –18mA
V_CC = Min.,V_IN = 0.0V
I_ON = 48mA or 64mA
PI3C3384
PI3C32384
V_CC = Min.,V_IN = 2.4V
I_ON = 15mA
PI3C3384
PI3C32384
— –0.73 –1.2
—
5
7
18 28 40
—
8
15
18 35 48
Units
V
µA
V
Ω
Capacitance (T_A = 25°C f = 1 MHz)
Parameters⁽⁵⁾
Description
Test Conditions Typ. Units
C_IN
Input Capacitance
3.5
C_OFF
A/B Capacitance, Switch Off
V_IN = 0V
5.0 pF
C_ON
A/B Capacitance, Switch On
10.0
Notes:
1. ForMax.orMin.conditions,useappropriatevaluespecifiedunderElectricalCharacteristicsforthe
applicable device type.
2. Typical values are at V_CC = 3.3V, T_A = 25°C ambient and maximum loading.
3. Not more than one output should be shorted at one time. Duration of the test should not
exceed one second.
4. MeasuredbythevoltagedropbetweenAandBpinatindicatedcurrentthroughtheswitch.ONresistance
is determined by the lower of the voltages on the two (A,B) pins.
5. Thisparameterisdeterminedbydevicecharacterizationbutisnotproductiontested.
2
PS8161C 02/04/00