PI3C32160 Datasheet, PDF (2/4 Pages) Pericom Semiconductor Corporation – 3.3V, High Bandwidth,16:32-Bit, PCI Hot-Plug Mux/Demux Bus Switch

PI3C32160
3.3V, High Bandwidth, 16:32-Bit,
112233445566778899001122334455667788990011223344556677889900112211223344556677889900112233445566778899001122334455667788990011221122334455667788990011223344556677889900112233445566^P7788^C9900^I1122^H1122^o3344^t55^-66^P7788^l99^u00^g1122^M334455^u6677^x88^/99^D001122^e33^m445566^u77^x8899^B0011^u2211^s2233^S44^w556677ⁱ88^t99^c00^h1122
Maximum Ratings
(Above which the useful life may be impaired. For user guidelines, not tested.)
Storage Temperature ......................................... –65°Cto+150°C
Note:
Stresses greater than those listed under MAXIMUM RATINGS
Ambient Temperature with Power Applied .........–40°C to +85°C _{may cause permanent damage to the device. This is a stress rating}
Supply Voltage to Ground Potential .................... –0.5Vto+4.6V
DC I/O Voltage ....................................................... –0.5Vto5.5V
only and functional operation of the device at these or any other
conditions above those indicated in the operational sections of this
specification is not implied. Exposure to absolute maximum rating
DC Output Current ........................................................... 120mA _{conditions for extended periods may affect reliability.}
Power Dissipation .............................................................. 0.5W
DC Electrical Characteristics (Over the Operating Range, T_A = –40°C, V_CC = 3.3V ±10%, V_BIAS = 1.3V to V_CC)
Parameters
Description
Test Conditions⁽¹⁾
Min. Typ⁽²⁾ Max.
V_IH
Input HIGH Voltage
Guaranteed Logic HIGH Level
2.0 — —
V_IL
Input LOW Voltage
Guaranteed Logic LOW Level
–0.5 — 0.8
I_IH
Input HIGH Current
V_CC = Max., V_IN = V_CC
— — ±1
I_IL
Input LOW Current
V_CC = Max., V_IN= GND
— — ±1
I_OZH
High Impedance Output Current A= 0V or V_CC max., V_BIAS1 = V_BIAS2 =V_CC max. —
±1
I_O
Pullup Current
B = 0V or V_CC max., V_BIAS1 = V_BIAS2 =V_CC max. –0.2 —
–2
V_IK
Clamp Diode Voltage
R_ON
Switch ON Resistance⁽⁴⁾
V_CC = Min., I_IN = –18mA
V_CC = Min., V_IN = 0.0mA
I_ON = 48mA or 64mA
— –0.73 –1.2
— 9.0 12
V_CC = Min., I_IN = 2.4V
I_ON = 15mA
— 16 23
Units
V
V
µA
µA
µA
mA
V
Ω
Ω
Capacitance (T_A = 25°C, f = 1 MHz)
Parameters⁽⁵⁾
Description
C_IN
C_OFF
Input Capacitance
A/B Capacitance, Switch Off
C_ON
A/B Capacitance, Switch Off
Test Conditions
V_IN = 0V
Typ.
Max.
Units
3.5
—
4.0
—
pF
12.0
—
Notes:
1. For Max. or Min. conditions, use appropriate value specified under Electrical Characteristics for the applicable device type.
2. Typical values are at V_CC = 3.3V, T_A = 25°C ambient and maximum loading.
3. Not more than one output should be shorted at one time. Duration of the test should not exceed one second.
4. Measured by the voltage drop between A and B pins at indicated current through the switch. ON resistance is determined by the
lower of the voltages on the two (A & B) pins.
5. This parameter is determined by device characterization but is not production tested.
2
PS8453F 03/09/01