PI3C16225 Datasheet, PDF (2/4 Pages) Pericom Semiconductor Corporation – 3.3V, High Bandwidth, Low Capacitance 12-Bit to 24-Bit Mux/Demux Bus Switch (16292 Pinout)

PI3C16225
3.3V, High Bandwidth, Low Capacitance 12-Bit to
1122334455667788990011223344556677889900112233445566778899001122112233445566778899001122334455667788990011223344556677889900112211223344556677889900112233445566²77⁴8899^-00^B1122ⁱ33^t4455^M6677^u8899^x0011^/22^D1122^e33^m445566^u7788^x9900^B1122^u33^s4455^S6677^w8899ⁱ00^t11^c22^h334455⁽66¹77⁶8899²00⁹1122²1122^P3344ⁱ55ⁿ66^o7788^u9900^t11⁾22
Maximum Ratings
(Above which the useful life may be impaired. For user guidelines, not tested.)
Storage Temperature .......................................................... –65°C to +150°C
Ambient Temperature with Power Applied .............................. –40°Cto+85°C
Supply Voltage to Ground Potential (Inputs & V_CC Only) ......... –0.5Vto+4.6V
Supply Voltage to Ground Potential (Outputs & D/O Only) .......–0.5Vto+4.6V
DCI/OVoltage ..........................................................................–0.5Vto+5.5V
DC Output Current ............................................................................... 120mA
Power Dissipation ................................................................................... 0.5W
Note:
Stresses greater than those listed under MAXIMUM
RATINGS may cause permanent damage to the
device. This is a stress rating only and functional
operation of the device at these or any other condi-
tions above those indicated in the operational sections
of this specification is not implied. Exposure to
absolute maximum rating conditions for extended
periods may affect reliability.
DC Electrical Characteristics (Over the Operating Range, T_A = –40°C to +85°C, V_CC = 3.3V ±10%)
Parameters
Description
Test Conditions⁽¹⁾
Min. Typ.⁽²⁾ Max.
V_IH
Input HIGH Voltage
Guaranteed Logic HIGH Level
2.0 —
—
V_IL
Input LOW Voltage
Guaranteed Logic LOW Level
–0.5 —
0.8
I_IH
Input HIGH Current
V_CC = Max., V_IN = V_CC
—
—
±1
I_IL
Input LOW Current
V_CC = Max., V_{IN =} GND
—
—
±1
I_O
B-port Pulldown Current
V_CC = Min., V_O = V_CC
SEL = High for B1
SEL = Low for B2
2.5 3.8 —
V_IK
Clamp diode Voltage
V_CC = Min., I_IN = –18mA
— –0.73 –1.2
R_ON
Switch On Resistance⁽⁴⁾
V_CC = Min.,V_IN = 0.0V
I_ON = 48mA or 64mA
V_CC = Min.,V_IN = 2.4V
I_ON = 15mA
—
9
12
—
16
23
Units
V
µA
mA
V
Ω
Capacitance (T_A = 25°C f = 1 MHz)
Parameters⁽⁵⁾
Description
C_IN
Input Capacitance
C_ON
A/B Capacitance, Switch On
Test Conditions
V_IN = 0V
Typ.
Max. Units
3.5
—
pF
9.3
11
Notes:
1. For Max. or Min. conditions, use appropriate value specified under Electrical Characteristics for the applicable device type.
2. Typical values are at V_CC = 3.3V, T_A = 25°C ambient and maximum loading.
3. Not more than one output should be shorted at one time. Duration of the test should not exceed one second.
4. Measured by the voltage drop between A and B pin at indicated current through the switch. ON resistance is determined by the
lower of the voltages on the two (A,B) pins.
5. This parameter is determined by device characterization but is not production tested.
2
PS8458D 03/13/01