PI3B32X384_06 Datasheet, PDF (2/4 Pages) Pericom Semiconductor Corporation – 3.3V, 20-Bit, 2-Port NanoSwitch

PI3B32X384
3.3V, 20-Bit, 2-Port NanoSwitch™
Maximum Ratings
(Above which the useful life may be impaired. For user guidelines, not tested.)
Storage Temperature ............................................................ –65°C to +150°C
Ambient Temperature with Power Applied............................ –40°C to +85°C
Supply Voltage to Ground Potential........................................–0.5V to +4.6V
DC Input Voltage.....................................................................–0.5V to +4.6V
DC Output Current...............................................................................120mA
Power Dissipation ................................................................................... 0.5W
Note:
Stresses greater than those listed under MAXIMUM RAT-
INGS may cause permanent damage to the device. This is
a stress rating only and functional operation of the device
at these or any other conditions above those indicated in
the operational sections of this specification is not implied.
Exposure to absolute maximum rating conditions for ex-
tended periods may affect reliability.
DC Electrical Characteristics (Over the Operating Range, T_A = –40°C to +85°C, V_CC = 3.3V ±10%)
Parameters
Description
Test Conditions(1)
Min.
Typ⁽²⁾
V_IH
Input HIGH Voltage
Guaranteed Logic HIGH Level
2.0
—
V
Input LOW Voltage
IL
Guaranteed Logic LOW Level
-0.5
—
I_IH
Input HIGH Current
V_CC = Max. V_IN = V_CC
—
—
I_IL
Input LOW Current
V_CC = Max. V_IN = GND
—
—
I_OZH
High-Impedance Output Current
0 ≤ A, B ≤ V_CC
—
—
V
Clamp Diode Voltage
IK
V = Min. I = -18mA
CC
IN
—
—
R
Switch ON Resistance⁽⁴⁾
ON
V = Min. V = 0.0V
CC
IN
I = 15mA
ON
V_CC = Min. V_IN = 2.4V
I = 15mA
ON
—
5
—
10
Max.
—
0.8
±1
±1
±1
-1.2
8
17
Units
V
V
µA
µA
µA
V
Ω
Notes:
1. For Max. or Min. conditions, use appropriate value specified under Electrical Characteristics for the applicable device type.
2. Typical values are at V_CC = 3.3V, T_A = 25°C ambient and maximum loading.
3. Measured by the voltage drop between A and B pin at indicated current through the switch. ON resistance is determined by the lower of the volt-
ages on the two (A,B) pins.
Capacitance (T_A = 25°C, f = 1 MHz)
Parameters
Description
Test Conditions Typ
C_IN
INput Capacitance
V_IN = 0V
—
C_OFF
A/B Capacitance, Switch Off
V_IN = 0V
—
C
A/B Capacitance, Switch On
V = 0V
—
ON
IN
Max.
3.0
8.0
16.0
Units
pF
pF
pF
Notes:
1. This parameter is determined by device characterization but is not production tested.
2. Typical values are at V_CC = 3.3V, T_A =25°C ambient and maximum loading.
3. Not more than one output should be sorted at one time. Duration of the test should not exceed one second.
4. Measured by the voltage drop between A and B pin at indicated current through the switch. ON resistance is determined by the lower of the volt-
ages on the two (A,B) pins.
5. This parameter is determined by device characterization but is not production tested.
06-0312
2
PS8336F
12/04/06