PI3B3245 Datasheet, PDF (2/5 Pages) Pericom Semiconductor Corporation – 3.3V, Hot Insertion 8-Bit, 2-Port, NanoSwitch

PI3B3245
3.3V, Hot Insertion
11223344556677889900112233445566778899001122334455667788990011221122334455667788990011223344556677889900112233445566778899001122112233445566778899001122334455667788990011223344556677889900112211223344556677⁸88^-99^B0011ⁱ22^t33^,4455²66^-77^P8899^o0011^r22^t33^,4455^N6677^a8899ⁿ00^o1122^S1122^w3344ⁱ55^tc6677^h8899^™001122
Maximum Ratings
(Above which the useful life may be impaired. For user guidelines, not tested.)
Storage Temperature ..................................................................... –65°C to +150°C
Ambient Temperature with Power Applied ..................................... –40°C to +85°C
Supply Voltage to Ground Potential ................................................. –0.5Vto+4.6V
DC Input Voltage .............................................................................. –0.5Vto+4.6V
DC Output Current ....................................................................................... 120mA
Power Dissipation ............................................................................................ 0.5W
Note:
Stresses greater than those listed under MAXIMUM RATINGS may cause permanent
damage to the device. This is a stress rating only and functional operation of the device
at these or any other conditions above those indicated in the operational sections of this
specification is not implied. Exposure to absolute maximum rating conditions for
extended periods may affect reliability.
DC Electrical Characteristics (Over the Operating Range, T_A = –40°C to +85°C, V_CC =3.3V ±10%)
Parameters Description
Test Conditions⁽¹⁾
Min. Typ⁽²⁾
V_IH
Input HIGH Voltage
Guaranteed Logic HIGH Level
2.0
V_IL
Input LOW Voltage
Guaranteed Logic LOW Level
–0.5
I_IH
Input HIGH Current
V_CC = Max., V_IN = V_CC
I_IL
Input LOW Current
V_CC = Max., V_IN = GND
I_OZH
High Impedance Output Current 0 ≤ IN, YN ≤ VCC
V_IK
Clamp Diode Voltage
V_CC = Min., I_IN = –18mA
R_ON
Switch On Resistance⁽³⁾
V_CC = Min., V_IN = 0.0V, I_ON = 48mA or 64mA
5
V_CC = Min., V_IN = 2.4V,I_ON = 15mA
10
Max.
0.8
±1
±1
±1
–1.2
8
17
Units
V
V
µA
µA
µA
V
Ω
Capacitance (T_A = 25°C, f = 1 MHz)
Parameters⁽⁴⁾ Description
Test Conditions
Typ. Units
C_IN
C_OFF
C_ON
Input Capacitance
A/B Capacitance, Switch Off
A/B Capacitance, Switch On
V_IN = 0V
V_IN = 0V
V_IN = 0V
3.0
pF
8.0
pF
16.0
pF
Notes:
1. For Max. or Min. conditions, use appropriate value specified under Electrical Characteristics for the applicable device type.
2. Typical values are at V_CC = 3.3V, T_A = 25°C ambient and maximum loading.
3. Measured by the voltage drop betweenAand B pin at indicated current through the switch. ON resistance is determined
by the lower of the voltages on the two (A,B) pins.
4. This parameter is determined by device characterization but is not production tested.
2
PS8162F 09/23/04