PI3B32160 Datasheet, PDF (2/4 Pages) Pericom Semiconductor Corporation – 3.3V, Low Capacitance 16-Bit to 32-Bit, DeMux NanoSwitch™ with Precharged Outputs

PI3B32160
3.3V, Low Capacitance 16-Bit to 32-Bit, Demux PCI Hot Plug
112233445566778899001122334455667788990011223344556677889900112211223344556677889900112233445566778899001122334455667788990011221122334455^B6677^u8899^s00^S1122^w3344ⁱ55^t66^c7788^h9900^w1122ⁱ33^t44^h5566^P7788^r99^e0011^c22^h1122^a33^r4455^g66^e7788^d9900^O1122^u3344^t55^p6677^u88^t99^s0011^f22^o3344^r55^L6677ⁱ88^v9900^e1122^I11ⁿ2233^s44^e55^r6677^t88^io9900ⁿ1122
Maximum Ratings
(Above which the useful life may be impaired. For user guidelines, not tested.)
Storage Temperature............................................................ –65°C to +150°C
Ambient Temperature with Power Applied ........................... –40°C to +85°C
Supply Voltage to Ground Potential (Inputs & V_CC Only) ... –0.3V to +4.6V
Supply Voltage to Ground Potential (Outputs & D/O Only) . –0.5V to +4.6V
DC Input Voltage ................................................................... –0.5V to +4.6V
DC Output Current .............................................................................. 120mA
Power Dissipation ................................................................................... 0.5W
Note:
Stresses greater than those listed under MAXIMUM
RATINGS may cause permanent damage to the de-
vice. This is a stress rating only and functional opera-
tion of the device at these or any other conditions
above those indicated in the operational sections of
this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may
affect reliability.
DC Electrical Characteristics (Over the Operating Range, T_A = –40°C to +85°C, V_CC = 3.3V ±10%, VBIAS = 1.3V to V_CC)
Parameters Description
Test Conditions⁽¹⁾
Min. Typ.⁽²⁾ Max. Units
V_IH
Input HIGH Voltage
V_IL
Input LOW Voltage
Guaranteed Logic HIGH Level
Guaranteed Logic LOW Level
2.0
—
—
–0.5 —
0.8
V
I_IH
Input HIGH Current
V_CC = Max., V_IN = V_CC
—
—
±1
I_IL
Input LOW Current
V_CC = Max., V_IN = GND
—
—
±1
µA
I_OZH
High Impedance Output Current A=0VorV_CCmax.,VBIAS1=VBIAS2=V_CCmax. —
—
+1
V_IK
Clamp Diode Voltage
R_ON
Switch On Resistance⁽⁴⁾
V_CC = Min., I_IN = –18mA
V_CC = Min., V_IN = 0.0V,
I_ON = 48mA
V_CC = Min., V_IN = 2.4V,
I_ON = 15mA
— –0.9 –1.8 V
—
5
7
Ω
—
9
15
Capacitance (T_A = 25°C, f = 1 MHz)
Parameters⁽⁵⁾ Description
C_IN
C_OFF
Input Capacitance
A Capacitance, Switch Off
C_OFF
C_ON
B Capacitance, Switch Off
A/B Capacitance, Switch On
Test Conditions
V_IN = 0V
V_IN = 0V
V_IN = 0V
V_IN = 0V
Typ. Max.
2.6
3.2
8.0
9.5
4.2
4.7
11
14
Units
pF
Notes:
1. For Max. or Min. conditions, use appropriate value specified under Electrical Characteristics for the applicable device type.
2. Typical values are at V_CC = 3.3V, T_A= 25°C ambient and maximum loading.
3. Not more than one output should be shorted at one time. Duration of the test should not exceed one second.
4. Measured by the voltage drop between A and B pins at indicated current through the switch. ON resistance is determined by the lower
of the voltages on the two (A & B) pins.
5. This parameter is determined by device characterization but is not production tested.
2
PS8420C 05/04/00