PI3B16245_04 Datasheet, PDF (2/5 Pages) Pericom Semiconductor Corporation – 3.3V, 16-Bit, 2-Port NanoSwitch™

PI3B16245
11223344556677889900112233445566778899001122334455667788990011221122334455667788990011223344556677889900112233445566778899001122112233445566778899001122334455667788990011223344556677889900³1122^.11³22^V334455^, 6677¹88⁶9900^-11^B2233ⁱ44^t55^,66²7788^-99^P0011^o22^r3344^t5566^N7788^a99ⁿ0011^o2211^S22^w3344ⁱ55^t66^c7788^h99^™001122
Maximum Ratings
(Above which useful life may be impaired. For user guidelines, not tested.)
Storage Temperature ...................................................... –65°C to +150°C
Ambient Temperature with Power Applied ...................... –40°C to +85°C
Supply Voltage Range ....................................................... –0.5Vto+4.6V
DC Input Voltage ............................................................... –0.5Vto+4.6V
DC Output Current ........................................................................120mA
Power Dissipation ............................................................................. 0.5W
Note:
Stresses greater than those listed under MAXIMUM RAT-
INGS may cause permanent damage to the device. This is a
stress rating only and functional operation of the device at
these or any other conditions above those indicated in the
operational sections of this specification is not implied.
Exposure to absolute maximum rating conditions for extended
periods may affect reliability.
DC Electrical Characteristics (Over the Operating Range, T_A = –40°C to +85°C, V_CC = 3.0V to 3.6V)
Parameters
Description
Test Conditions⁽¹⁾
Min. Typ.⁽²⁾
V_IH
Input HIGH Voltage
Guaranteed Logic HIGH
2.0
Level
V_IL
Input LOW Voltage
Guaranteed Logic LOW
–0.5
Level
I_IH
Input HIGH Current
V_CC = Max., V_IN = V_CC
I_IL
Input LOW Current
V_CC = Max., V_IN = GND
I_{O ZH}
High Impedance Output Current 0 ≤ A, B ≤ V_CC
V_IK
Clamp Diode Voltage
V_CC = Min., I_IN = –18mA
–0.7
R_{O N}
Switch ON Resistance⁽³⁾
V_CC = Min., V_IN = 0.0V,
5
I_ON = 48mA
V_CC = Min., V_IN = 2.4V,
10
I_ON = 15mA
Max.
0.8
±1
±1
±1
–1.2
8
15
Units
V
µA
V
Ω
Capacitance (T_A = 25°C, f = 1 MHz)
Parameters⁽⁴⁾
Description
Test Conditions
Typ.
Units
C_IN
C_OFF
C_ON
Input Capacitance
A/B Capacitance, Switch Off
A/B Capacitance, Switch On
V_IN = 0V
3.0
8.5
pF
17.0
Notes:
1. For Max. or Min. conditions, use appropriate value specified under Electrical Characteristics for the applicable device type.
2. Typical values are at V_CC = 3.3V, T_A = 25°C ambient and maximum loading.
3. Measured by the voltage drop between A and B pin at indicated current through the switch. On-Resistance is determined by the lower of the
voltages on the two (A,B) pins.
4. This parameter is determined by device characterization but is not production tested.
2
PS8189E 10/01/04