PI3B16215 Datasheet, PDF (2/5 Pages) Pericom Semiconductor Corporation – 3.3V, Hot Insertion, 20-Bit FET BusSwitch w/Precharged Outputs

PI3B16215
3.3V, Hot Insertion,
11223344556677889900112233445566778899001122334455667788990011221122334455667788990011223344556677889900112233445566778899001122112233445566778899001122334455667788²99⁰0011^-22^B3344ⁱ55^t66^F7788^E9900^T1122^B1122^u3344^s55^S6677^w8899ⁱ00^t11^c22^h3344^w556677^/88^P99^r0011^e22^c33^h4455^a6677^r88^g9900^e11^d2211^O2233^u4455^t66^p7788^u9900^t11^s22
Maximum Ratings
(Above which the useful life may be impaired. For user guidelines, not tested.)
Storage Temperature Range, T_STG ...................................... –65ºC to +150ºC
Supply Voltage Range, V_CC ......................................... –0.5V to +4.6V
Bias Voltage Range, BIASV ........................................ –0.5V to +4.6V
Input Voltage Range ........................................................–0.5V to +4.6V
DC Output Current ....................................................................... 120mA
Power Dissipation ............................................................................ 0.5W
Note:
Stresses greater than those listed under MAXIMUM
RATINGS may cause permanent damage to the device.
This is a stress rating only and functional operation of the
device at these or any other conditions above those
indicated in the operational sections of this specification
is not implied. Exposure to absolute maximum rating
conditions for extended periods may affect reliability.
Electrical Characteristics (Over the Operating Range, T_A = –40°C to +85°C, V_CC = 3.0V to 3.6V)
Parameter
Description
Test Conditions
Min. Typ. Max. Units
BIASV
V_IH
V_IL
Bias Voltage
High-Level Control Input Voltage
Low-Level Control Input Voltage
V_CC = 2.7V to 3.6V
V_CC = 2.7V to 3.6V
0
V_CC
2
V
–0.5
0.8
V_IK
I_I
I_OZH
I_O
I_CC
Clamp Diode Voltage
Input Current
High Impedance Output Current
Output Current
Quiescent Power Supply Current
∆I_CC(1) Supply Current
V_CC = 3.0V
V_CC = 3.6V
V_CC = 0
V_CC = 3.0V
V_CC = 3.6V
V_CC = 3.6V
I_I = –18mA
–0.7 –1.2
V_I = V_CC or GND
V_I = V_O = 0 to 3.6V
±5
µA
10
BIASV = 2.4V, V_O = 0 0.15
mA
I_O = 0, V_I = V_CC or GND
10
One Input at 3V,
Other Inputs at V_CC or
GND
µA
750
C_IN
C_OFF
Input Capacitance
A/B Capacitance Switch Off
V_I = 3.0V or 0
V_O = 3.0V or
0
Switch Off
3.0
pF
8.5
R_ON(2) Switch On Resistance
V_I = 0
I_I = 64mA
I_I = 24mA
5
8
5
8
Ω
V_I = 2.4V
I_I = 15mA
10 15
Notes:
1. This is the increase in supply current for each input (OE only) that is at the specified voltage level rather than V_CC or GND.
2. Measured by the voltage drop between the A and B terminals at the indicated current through the switch. On state
resistance is determined by the lower of the voltages of the two (A or B) terminals.
Truth Table
OE
Function
L
A port = B port
H
A port = Z, B Port = BIASV
2
PS8190D
05/04/00