PI2USB3212_14 Datasheet, PDF (2/8 Pages) Pericom Semiconductor Corporation – 5.0Gbps USB 3.0 Compatible 2:1 Mux/DeMux Switch

PI2USB3212
5.0Gbps USB 3.0 Compatible 2:1 Mux/DeMux Switch
Maximum Ratings
(Above which useful life may be impaired.For user guidelines, not tested.)
Storage Temperature.......................................... –65°C to +150°C
Supply Voltage to Ground Potential .................... –0.5V to +2.5V
DC Input Voltage.................................................. –0.5V to +V_DD
DC Output Current ........................................................... 120mA
Power Dissipation................................................................. 0.5W
Note: Stresses greater than those listed under MAXIMUM RATINGS
may cause permanent damage to the device. This is a stress rating only
and functional operation of the device at these or any other conditions
above those indicated in the operational sections of this specification
is not implied. Exposure to absolute maximum rating conditions for
extended periods may affect reliability.
Power Supply Characteristics
Parameters
Description
Test Conditions⁽¹⁾
Min. Typ.⁽²⁾
I_DD
Quiescent PowerSupply Current
V_DD = Max., V_IN = GND or V_DD
Notes:
1. For Max. or Min. conditions, use appropriate value specified under Electrical Characteristics for the applicable device type.
2. Typical values are at V_DD = 1.8V, T_a = 25°C ambient and maximum loading.
Max.
200
Units
µA
DC Electrical Characteristics for Switching over Operating Range
(T_A = –40°Cto +85°C, V_DD = 1.5V to 1.8V ±10%)
Parameter Description
Test Conditions
Min.
V_IH
Input HIGH Voltage, SEL input Guaranteed HIGH level
0.65 x V_DD
V_IL
Input LOW Voltage, SEL input Guaranteed LOW level
-0.5
V_IK
Clamp Diode Voltage, SEL input V_DD = Max., I_IN = –18mA
-
I_IH
Input HIGH Current, SEL input V_DD = Max., V_IN = V_DD
-5
I_IL
Input LOW Current, SEL input V_DD = Max., V_IN = GND
-5
V_DD= 1.5V +/-10%
RL = 50ohm, V_O/V_I >80%
-0.5
V_DD = 1.5V +/-10%
V_I DC
DC Input Signal Voltage Range
RL = 10Kohm, V_O/V_I >95%
V_DD = 1.8V ±10%
RL = 50ohm, V_O/V_I >80%
-0.4
V_DD = 1.8V ±10%
RL = 10Kohm, V_O/V_I >95%
Typ.
Max. Units
-
-
-
0.35 x V_DD V
-0.7
-1.2
-
+5
μA
-
+5
1.8
2.2
V
2.0
2.4
Switching Characteristics (TA= -40° to +85°C, VDD = 1.5V to 1.8V ± 10%)
Parameter
Description
tPZH, tPZL Line Enable Time - SEL to AN, BN, CN
tPHZ, tPLZ Line Disable Time - SEL to AN, BN, CN
tb-b
Bit-to-bit skew within the same differential pair
tch-ch
Channel-to-channel skew
t_PD
Propagation delay A to B or C / B or C to A
Min. Typ.
0.5
-
0.5
-
55
Notes:
1. For max. or min. conditions, use appropriate value specified under Electrical Characteristics for the applicable device type.
Max.
9.0
9.0
6
15
75
Units
ns
ps
14-0030
2
03/17/14