PI2DBS212_14 Datasheet, PDF (2/10 Pages) Pericom Semiconductor Corporation – 2.0GHz, Differential Broadband Signal Switch, 2-Differential Channel, 2:1 Mux/DeMux Switch

PI2DBS212
2.0GHz, Differential Broadband Signal Switch,
2-Differential Channel, 2:1 Mux/DeMux Switch
Maximum Ratings
(Above which useful life may be impaired. For user guidelines, not tested.)
Storage Temperature....................................–65°C to +150°C
Supply Voltage to Ground Potential...............–0.5V to +2.5V
DC Input Voltage ............................................–0.5V to V_DD
DC Output Current......................................................120mA
Power Dissipation...........................................................0.5W
Note:
Stresses greater than those listed under MAXIMUM RATINGS may cause
permanent damage to the device. This is a stress rating only and func-
tional operation of the device at these or any other conditions above those
indicated in the operational sections of this specification is not implied.
Exposure to absolute maximum rating conditions for extended periods
may affect reliability.
DC Electrical Characteristics over 1.8V Operating Range (TA= -40°C to +85°C, VDD = 1.8V ±10%)
Parameter
Description
Test Conditions⁽¹⁾
Min.
Typ.⁽²⁾
Max.
V_IH
Input HIGH Voltage
V_IL
Input LOW Voltage
V_IK
Clamp Diode Voltage
I_IH
Input HIGH Current
I_IL
Input LOW Current
R_ON
ON Resistance
C_ON
Capacitance ON (A/B)
Guaranteed HIGH level
Guaranteed LOW level
V_DD = Max., I_IN = –18mA
V_DD = Max., V_IN = V_DD
V_DD = Max., V_IN = GND
V_DD = Min., V_IN = 1.3V, I_IN =
40mA
V_IN = 0, V_DD = 1.8V
0.65 x V_DD
–0.5
–0.7
3.5
0.35 x V_DD
–1.2
±5
±5
10
Notes:
1. For Max. or Min. conditions, use appropriate value specified under Electrical Characteristics for the applicable device type.
2. Typical values are at V_DD = 1.8V, T_a = 25°C ambient and maximum loading.
Units
V
µA
Ohm
pF
Power Supply Characteristics over 1.8V Operating Range (TA= -40°C to +85°C, VDD = 1.8V ±10%)
Parameters
Description
Test Conditions⁽¹⁾
Min. Typ.⁽²⁾ Max.
V_DD = MAX, V_IN and V_SEL = GND or
I_DD
Quiescent Power Supply Current V_DD
400
Notes:
1. For Max. or Min. conditions, use appropriate value specified under Electrical Characteristics for the applicable device type.
2. Typical values are at V_DD = 1.8V, T_a = 25°C ambient and maximum loading.
Units
µA
Switching Characteristics over 1.8V Operating Range (TA= -40°C to +85°C, VDD = 1.8V ±10%)
Parameter
Description⁽¹⁾
Min. Typ. Max.
t_PZH, t_PZL Line Enable Time - SEL to A_N, B_N
0.5
8.0
t_PHZ, t_PLZ Line Disable Time - SEL to A_N, B_N
0.5
4.0
t_b-b
t_ch-ch
t_PD
Bit-to-bit skew, within same differential pair
Channel-to-channel timing skew
Propagation Delay, A to B or C / B or C to A
5
12
50
150
Notes:
1. For max. or min. conditions, use appropriate value specified under Electrical Characteristics for the applicable device type.
Units
ns
ps
14-0029
2
www.pericom.com
03/25/14