EPA1140_15 Datasheet, PDF (1/1 Pages) PCA ELECTRONICS INC. – SMD 8 Pin 5 Tap TTL Compatible

ELECTRONICS INC.
SMD 8 Pin 5 Tap TTL Compatible
Active Delay Lines
EPA1140-XX & EPA1140-XX-RC
Add “-RC” after part number for RoHS Compliant
PCA
Part Number
EPA1140-25(-RC)
EPA1140-30(-RC)
EPA1140-35(-RC)
EPA1140-40(-RC)
EPA1140-45(-RC)
EPA1140-50(-RC)
EPA1140-60(-RC)
EPA1140-75(-RC)
EPA1140-100(-RC)
EPA1140-125(-RC)
Tap Delays
(†±5% or ± 2nS)
5, 10, 15, 20
6, 12, 18, 24
7, 14, 21, 28
8, 16, 24, 32
9, 18, 27, 36
10, 20, 30, 40
12, 24, 36, 48
15, 30, 45, 60
20, 40, 60, 80
25, 50, 75, 100
Total Delay
(†±5% or ± 2nS)
25
30
35
40
45
50
60
75
100
125
PCA
Part Number
EPA1140-150(-RC)
EPA1140-175(-RC)
EPA1140-200(-RC)
EPA1140-225(-RC)
EPA1140-250(-RC)
EPA1140-300(-RC)
EPA1140-350(-RC)
EPA1140-400(-RC)
EPA1140-450(-RC)
EPA1140-500(-RC)
Tap Delays
(†±5% or ± 2nS)
30, 60, 90, 120
35, 70, 105, 140
40, 80, 120, 160
45, 90, 135, 180
50, 100, 150, 200
60, 120, 180, 240
70, 140, 210, 280
80, 160, 240, 320
90, 180, 270, 360
100, 200, 300, 400
Total Delay
(†±5% or ± 2nS)
150
175
200
225
250
300
350
400
450
500
†Whichever is greater. Delay times referenced from input to leading and trailing edges at 25°C, 5.0V, with no load.
DC Electrical Characteristics
Parameter
Test Conditions
Min. Max. Unit
VOH High-Level Output Voltage VCC = min. VIL= max. IOH = max 2.7
VOL Low-Level Output Voltage VCC = min. VIH = min. IOL= max
VIK Input Clamp Voltage
VCC = min. II = II _K
IIH High-Level Input Current VCC = max. VIN = 2.7V
VCC = max. VIN = 5.25V
IIL Low-Level Input Current
VCC = max. VIN = 0.5V
IOS Short Circuit Output Current VCC = max. V _OUT = 0.
-40
(One output at a time)
ICCH High-Level Supply Current
ICCL Low-Level Supply Current
TRO Output Rise Time
NH Fanout High-Level Output
NL Fanout Low-Level Output
VCC = max. VIN = OPEN
VCC = max. VIN = 0
Td ≤ 500 nS (0.75 to 2.4 Volts)
VCC = max. V _OH = 2.7V
VCC = max. V _OL = 0.5V
V
0.5 V
-1.2 V
50 µA
1.0 mA
-2 mA
-100 _mA
75 mA
75 mA
4 nS
20 TTL Load
10 TTL Load
Schematic
8
VCC 7 2 6 3 5 OUTPUT
INPUT 1
4 GROUND
Package
.030
(.762)
Recommended Operating Conditions Min. Max. Unit
VCC
VIH
VIL
IIK
IOH
IOL
PW*
d*
Supply Voltage
High-Level Input Voltage
Low-Level Input Voltage
Input Clamp Current
High-Level Output Current
Low-Level Output Current
Pulse Width of Total Delay
Duty Cycle
4.75 5.25 V
2.0
V
0.8 V
-18 mA
-1.0 mA
20 mA
40
%
40 %
TA Operating Free-Air Temperature -55 +125 °C
*These two values are inter-dependent.
.400
PCA
.280
Max. ^{EPA1140-25(-RC)} Max.
(10.16)
D.C.
(7.11)
.055
(1.40)
Pad Layout
.410
(10.41)
.250
Max.
(6.35)
.100
(2.54)
.500 Max.
.010
Typ.
(.254)
.100
(2.54)
.020
(.508)
.050
(1.27)
.300
(7.62)
Input Pulse Test Conditions @ 25° C
EIN Pulse Input Voltage
3.2
PW Pulse Width % of Total Delay
110
TRI Pulse Rise Time (0.75 - 2.4 Volts)
2.0
PRR Pulse Repetition Rate @ Td ≤ 200 nS 1.0
Pulse Repetition Rate @ Td > 200 nS 100
VCC Supply Voltage
5.0
Unit
Volts
%
nS
MHz
KHz
Volts
Notes :
1. Lead Finish
EPA1140-XX
SnPb
EPA1140-XX-RC
Hot Tin Dip (Sn) †
2. Peak Temperature Rating
225°C
260°C
4. Weight
.976 grams
.976 grams
5. Packaging Information
(Tube) TBD pieces/tube
(*Add “TR” to end of part
number, but in front of
“-RC”when placing order)
(Tape & Reel)
TBD pieces/13” reel
(*EPA1140-XXTR)
TBD pieces/tube
TBD pieces/13” reel
(*EPA1140-XXTR-RC)
† Lead Material : Matte Tin with Ni Barrier
PCA ELECTRONICS, INC.
16799 SCHOENBORN ST.
NORTH HILLS, CA 91343
Unless Otherwise Specified Dimensions are in Inches /mm ± .010 /.25
Product performance is limited to specified parameters. Data is subject to change without prior notice.
CSA1140-XX & -RC Rev. B 8/17/06 RR
TEL: [phone]
FAX: [phone]
http://www.pca.com