KBU6A_03 Datasheet, PDF (1/2 Pages) Pan Jit International Inc. – SILICON SINGLE-PHASE BRIDGE RECTIFIER

DATA SHEET
KBU6A~KBU6K
SILICON SINGLE-PHASE BRIDGE RECTIFIER
VOLTAGE ^{50 to 800 Volts} CURRENT 6.0 Amperes ^KBU
Recongnized File # E111753
FEATURES
• Plastic material has Underwriters Laboratory
Flammability Classification 94V-O
• Ideal for printed circuit board
• Reliable low cost construction utilizing molded plastic technique
• High temperature soldering guaranteed:
260°C/10 seconds/.375"(9.5mm) lead length at 5 lbs. (2.3kg) tension
• Both normal and Pb free product are available :
Normal : 80~95% Sn, 5~20% Pb
Pb free: 98.5% Sn above
MECHANICAL DATA
Case: Reliable low cost construction utilizing
molded plastic technique
Terminals: Leads solderable per MIL-STD-202,
Method 208
Mounting position: Any
Mounting torque: 5 in. lb. Max.
Weight: 0.3 ounce, 8.0 grams
MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS
Rating at 25°Cambient temperature unless otherwise specified. Resistive or inductive load, 60Hz.
For Capacitive load derate current by 20%.
Unit: inch (mm)
.933(23.7)
.894(22.7)
.220(5.6)
.181(4.6)
.052(1.3)
.047(1.2)
PA R A M E TE R
M axim um R ecurrent P eak R everse V oltage
S YM B O L K B U 6A K B U 6B K B U 6D K B U 6G K B U 6J K B U 6K U N ITS
VRRM
50
100 200 400 600 800
V
M axim um R M S B ridge Input V oltage
V RM S
35
70
140 280 420 560
V
M axim um D C B locking V oltage
VDC
50
M axim um A verage F orw ard TC =100 ^O C
R ectified O utput C urrent at TA =40 ^O C
IA V
I²t R ating for fusing ( t<8.3m s)
I²t
P eak F orw ard S urge C urrent single sine-w ave superim posed on
IF S M
rated load (JE D E C m ethod)
M axim um F orw ard V oltage D rop per B ridge E lem ent at 6.0A
VF
M axim um R everse Leakage C urrent at R ated @ TA =25^O C
D c B locking V oltage @ TA =100^O C
Typical Therm al R esistance per leg (N ote 2)
(N ote 3)
IR
R θJA
R θJC
O perating Junction and S torage Tem perature R ange
TJ,TS TG
100 200 400 600 800
V
6 .0
A
127
A ²sec
175
A pk
1 .0
5
1000
8 .6
3 .1
-55 to + 150
V pk
uA
O _{C /W}
O_C
NOTES:
1. Recommended mounting position is to bolt down on heatsink with silicone thermal compound for maximum heat transfer with #6 screw.
2. Units Mounted in free air, no heatsink, P.C.B at 0.375"(9.5mm) lead length with 0.5 x 0.5"(12 x 12mm)copper pads.
3. Units Mounted on a 2.0 x 1.6" x 0.3" thick (5 x 4 x 0.8cm) AL plate.
STAD-MAR.16.2003
PAGE . 1