GBU8A_04 Datasheet, PDF (1/2 Pages) Fairchild Semiconductor – Bridge Rectifiers

DATA SHEET
GBU8A thru GBU8K
GLASS PASSIVATED SINGLE-PHASE BRIDGE RECTIFIER
VOLTAGE 50 to 800 Volts POWER 8.0 Amperes ^GBU
Recongized File #E111753
FEATURES
• Plastic material has Underwriters Laboratory Flammability Classification 94V-O
• Ideal for printed circuit board
• Reliable low cost construction utilizing molded plastic technique
• Pb free product are available : 99% Sn above can meet Rohs environment
substance directive request
.880(22.3)
.860(21.8)
.160(4.1)
.140(3.5)
MECHANICAL DATA
Case: Reliable low cost construction utilizing molded plastic technique
Terminals: Leads solderable per MIL-STD-202G,
Method 208
Mounting position: Any
Mounting torque: 5 in. lb. Max.
Weight: 0.15 ounce, 4.0 grams
.100(2.54)
.085(2.16)
.080(2.03)
.065(1.65)
.190(4.83)
.210(5.33)
.050(1.27)
.040(1.02)
Unit: inch (mm)
.140(3.56)
.130(3.30)
.040(1.02)
.030(0.76)
.030(0.75)
.017(0.45)
MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS
Rating at 25°Cambient temperature unless otherwise specified. Resistive or inductive load, 60Hz.
For Capacitive load derate current by 20%.
PA R A M E TE R
S YM B O L G B U 8A G B U 8B G B U 8D G B U 8G G B U 8J G B U 8K U N ITS
M axim um R ecurrent P eak R everse V oltage
V RRM
50
100 200 400 600 800
V
M axim um R M S B ridge Input V oltage
VRM S
35
70
140 280 420 560
V
M axim um D C B locking V oltage
VDC
50
M axim um A verage F orw ard TC =100 ^O C
R ectified O utput C urrent at TA =40 ^O C
IA V
I²t R ating for fusing ( t<8.3m s)
I²t
P eak F orw ard S urge C urrent single sine-w ave superim posed on
rated load (JE D E C m ethod)
IFS M
M axim um Instantaneous F orw ard V oltage D rop per elem ent at 4.0A
VF
M axim um R everse Leakage C urrent at R ated @ TA =25^O C
D c B locking V oltage @ TA =100^O C
Typical Therm al R esistance per leg (N ote 2)
(N ote 3)
IR
R θJA
R θJC
O perating Junction and S torage Tem perature R ange
TJ,TS TG
100 200 400 600 800
V
8 .0
6 .0
A
16 6
A ²sec
200
Ap k
1 .0
5 .0
500
1 8 .0
3 .0
-55 to + 150
V pk
uA
O _{C /W}
O_C
NOTES:
1. Recommended mounting position is to bolt down on heatsink with silicone thermal compound for maximum heat transfer with #6 screw.
2. Units Mounted in free air, no heatsink, P.C.B at 0.375"(9.5mm) lead length with 0.5 x 0.5"(12 x 12mm)copper pads.
3. Units Mounted on a 2.6 x 1.4" x 0.06" thick ( 6.5 x 3.5 x 0.15cm) AL plate.
STAD-AUG.19.2004
PAGE . 1