GBU10A_04 Datasheet, PDF (1/2 Pages) Pan Jit International Inc. – GLASS PASSIVATED SINGLE-PHASE BRIDGE RECTIFIER

DATA SHEET
GBU10A~GBU10K
GLASS PASSIVATED SINGLE-PHASE BRIDGE RECTIFIER
VOLTAGE 50 to 800 Volts CURRENT ^{10 Amperes GBU}
Recongnized File #E228882
FEATURES
• Plastic material has Underwriters Laboratory Flammability Classification 94V-O
• Ideal for printed circuit board
• Reliable low cost construction utilizing molded plastic technique
• Surge overload rating: 200 Amperes peak
• High temperature soldering guaranteed:
260°C/10 seconds/.375"(9.5mm) lead length at 5 lbs. (2.3kg) tension
• Pb free product are available : 99% Sn above can meet Rohs environment substance
directive request
.880(22.3)
.860(21.8)
.160(4.1)
.140(3.5)
MECHANICAL DATA
Case: Reliable low cost construction utilizing
molded plastic technique
Terminals: Leads solderable per MIL-STD-202, Method 208
Mounting position: Any
Mounting torque: 5 in. lb. Max.
Weight: 0.15 ounce, 4.0 grams
.100(2.54)
.085(2.16)
.080(2.03)
.065(1.65)
.190(4.83)
.210(5.33)
.050(1.27)
.040(1.02)
Unit: inch (mm)
.140(3.56)
.130(3.30)
.040(1.02)
.030(0.76)
.030(0.75)
.017(0.45)
MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS
Rating at 25°Cambient temperature unless otherwise specified. Resistive or inductive load, 60Hz. For Capacitive load derate current by 20%.
PA R A M E TE R
M axim um R ecurrent P eak R everse V oltage
S YM B O L G B U 10A G B U 10B G B U 10D G B U 10G G B U 10J G B U 10K U N ITS
VRRM
50
100
200
400
600
800
V
M axim um R M S B ridge Input V oltage
V RM S
35
70
140
280
420
560
V
M axim um D C B locking V oltage
VDC
50
100
200
400
600
800
V
M axim um A verage F orw ard TC =100 ^O C
R ectified O utput C urrent at TA =45^O C
IA V
1 0 .0
A
I²t R ating for fusing ( t<8.3m s)
I²t
166
A ²sec
P eak F orw ard S urge C urrent single sine-w ave superim posed
on rated load (JE D E C m ethod)
IF S M
200
A pk
M axim um Instantaneous F orw ard V oltage D rop per
elem ent at 5.0A
VF
1 .0
V pk
M axim um R everse Leakage C urrent at R ated @ TA =25^O C
D c B locking V oltage @ TA =100^O C
IR
5 .0
uA
500
Typical Therm al R esistance per leg (N ote 2)
(N ote 3)
R θJA
R θJC
8 .6
3 .1
O _{C /W}
O perating Junction and S torage Tem perature R ange
TJ,TS TG
-55 to + 150
O_C
NOTES:
1. Recommended mounting position is to bolt down on heatsink with silicone thermal compound for maximum heat transfer with #6 screw.
2. Units Mounted in free air, no heatsink, P.C.B at 0.375"(9.5mm) lead length with 0.5 x 0.5"(12 x 12mm)copper pads.
3. Units Mounted on a 2.6 x 1.4" x 0.06" thick ( 6.5 x 3.5 x 0.15cm) AL plate.
STAD-AUG.19.2004
PAGE . 1