GBJ8A_04 Datasheet, PDF (1/2 Pages) Pan Jit International Inc. – GLASS PASSIVATED SINGLE-PHASE BRIDGE RECTIFIER

DATA SHEET
GBJ8A~GBJ8K
GLASS PASSIVATED SINGLE-PHASE BRIDGE RECTIFIER
VOLTAGE 50 to 800 Volts CURRENT 8.0 Ampere
GBJ
Recongnized File #E228882
Unit: inch (mm)
FEATURES
• Plastic material has Underwriters Laboratory, Flammability Classification 94V-O
• Ideal for printed circuit board
• Reliable low cost construction utilizing molded plastic technique
• High temperature soldering guaranteed:
260°C/10 seconds/.375"(9.5mm) lead length at 5 lbs. (2.3kg) tension
• Both normal and Pb free product are available :
Normal : 80~95% Sn, 5~20% Pb
Pb free: 98.5% Sn above
MECHANICAL DATA
Case: Reliable low cost construction utilizing
molded plastic technique
Terminals: Leads solderable per MIL-STD-202,
Method 208
Mounting position: Any
Mounting torque: 5 in. lb. Max.
Weight: 0.15 ounce, 4.0 grams
.996(25.3)
.972(24.7)
.189(4.8)
.173(4.4)
.150(3.8)
.133(3.4)
.087(2.2)
.070(1.8)
.044(1.1)
.035(0.9)
.304(7.7)
.288(7.3)
.304(7.7)
.288(7.3)
.115(2.9)
.098(2.5)
.304(7.7)
.288(7.3)
.032(0.8)
.024(0.6)
MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS
Rating at 25°Cambient temperature unless otherwise specified. Resistive or inductive load, 60Hz.
For Capacitive load derate current by 20%.
PARAMETER
S YMB OL GB J 8 A GB J 8 B GB J 8 D GB J 8 G GB J 8 J GB J 8 K UNITS
Maximum Recurrent Peak Reverse Voltage
V RRM
50 100 200
400 600 800
V
Maxi mum RMS B ri dge Input Voltage
V RMS
35
70
140
280 420 560
V
Maximum DC Blocking Voltage
VDC
50 100 200
400 600 800
V
Maximum Average Forward TC=100 ^OC
Rectified Output Current at TA=40 ^OC
IAV
8.0
6.0
A
I²t Rati ng for fusi ng ( t<8.3ms)
I²t
166
A²sec
Peak Forward Surge Current single sine-wave superimposed
on rated load (JEDEC method)
Maxi mum Instantaneous Forward Voltage D rop per element
at 4.0A
Maximum Reverse Leakage Current at Rated @ TA=25^OC
Dc Blocking Voltage @ TA=100^OC
Typ i c a l The rma l Re s i s ta nc e p e r le g (No te 2 )
(Note 3)
IF S M
VF
IR
R θJ A
R θJ C
200
Apk
1.0
Vpk
5.0
500
uA
8.6
3.1
O_{C /W}
Op e ra ti ng J unc ti o n a nd S to ra g e Te mp e ra ture Ra ng e
TJ,TSTG
-55 to + 150
O_C
NOTES:
1. Recommended mounting position is to bolt down on heatsink with silicone thermal compound for maximum heat transfer with #6 screw.
2. Units Mounted in free air, no heatsink, P.C.B at 0.375"(9.5mm) lead length with 0.5 x 0.5"(12 x 12mm)copper pads.
3. Units Mounted on a 2.6 x 1.4" x 0.06" thick ( 6.5 x 3.5 x 0.15cm) AL plate.
STAD-APR.28.2004
PAGE . 1