GBJ8A Datasheet, PDF (1/2 Pages) Pan Jit International Inc. – GLASS PASSIVATED SINGLE-PHASE BRIDGE RECTIFIER(VOLTAGE - 50 to 800 Volts CURRENT - 8.0 Amperes)

Approve Sheet Part Number: GBJ8A~GBJ8K
DATA SHEET
GBJ8A~GBJ8K
GLASS PASSIVATED SINGLE-PHASE BRIDGE RECTIFIER
VOLTAGE - 50 to 800 Volts CURRENT - 8.0 Amperes
FEATURES
• Plastic material has Underwriters Laboratory
Flammability Classification 94V-O
• Ideal for printed circuit board
• Reliable low cost construction utilizing molded plastic technique
• Surge overload rating: 200Amperes peak
• High temperature soldering guaranteed:
260°C/10 seconds/.375"(9.5mm) lead length at 5 lbs. (2.3kg) tension
GBJ
0.996(25.3)
0.972(24.7)
MECHANICAL DATA
Case: Reliable low cost construction utilizing
molded plastic technique
Terminals: Leads solderable per MIL-STD-202,
Method 208
Mounting position: Any
Mounting torque: 5 in. lb. Max.
Weight: 0.15 ounce, 4.0 grams
0.087(2.2)
0.070(1.8)
0.044(1.1)
0.035(0.9)
0.304(7.7)
0.288(7.3)
0.304(7.7)
0.288(7.3)
MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS
Rating at 25°Cambient temperature unless otherwise specified. Resistive or inductive load, 60Hz.
For Capacitive load derate current by 20%.
Unit: inch ( mm )
0.189(4.8)
0.173(4.4)
0.150(3.8)
0.133(3.4)
0.115(2.9)
0.098(2.5)
0.304(7.7)
0.288(7.3)
0.032(0.8)
0.024(0.6)
Maximum Recurrent Peak Reverse Voltage
GBJ8A
50
Maximum RMS Input Voltage
35
Maximum DC Blocking Voltage
50
Maximum Average Forward T_C=100°C
Rectified Output Current TA= 45°C
I²t Rating for fusing ( t<8.3ms)
Peak Forward Surge Current single sine-wave superimposed on rated load
(JEDEC method)
Maximum Instantaneous Forward Voltage Drop per element at 8.0A
Maximum Reverse Leakage at rated T_A=25°
CDc Blocking Voltage per element T_C=100°C
Typical Thermal Resistance per leg(Note 2) RθJA
Typical Thermal Resistance per leg(Note 3) RθJC
Operating and Storage Temperature Range, TJ,TSTG
GBJ8B
100
70
100
GBJ8D
200
GBJ8G
400
GBJ8J
600
140
280
420
200
400
600
8.0
6.0
166
200
1.0
5
500
18.0
3.0
-55 to +150
GBJ8K
800
560
800
UNIT
V
V
V
A
A²sec
Apk
Vpk
µA
µA
°C / W
°C / W
°C
NOTES:
1. Recommended mounting position is to bolt down on heatsink with silicone thermal compound for maximum heat transfer with #6 screw.
2. Units Mounted in free air, no heatsink, P.C.B at 0.375"(9.5mm) lead length with 0.5 x 0.5"(12 x 12mm)copper pads.
3. Units Mounted on a 3.0 x 3.0" x 0.11" thick ( 7.5 x 7.5 x 0.3cm) AL plate.
PAGE . 1