GBJ4A Datasheet, PDF (1/2 Pages) Pan Jit International Inc. – GLASS PASSIVATED SINGLE-PHASE BRIDGE RECTIFIER(VOLTAGE - 50 to 800 Volts CURRENT - 4.0 Amperes)

DATA SHEET
GBJ4A~GBJ4K
GLASS PASSIVATED SINGLE-PHASE BRIDGE RECTIFIER
VOLTAGE - 50 to 800 Volts CURRENT - 4.0 Amperes
Recongnized File #E228882
FEATURES
• Plastic material has Underwriters Laboratory
Flammability Classification 94V-O
• Ideal for printed circuit board
• Reliable low cost construction utilizing molded plastic technique
• Surge overload rating: 150 Amperes peak
• High temperature soldering guaranteed:
260°C/10 seconds/.375"(9.5mm) lead length at 5 lbs. (2.3kg) tension
MECHANICAL DATA
Case: Reliable low cost construction utilizing
molded plastic technique
Terminals: Leads solderable per MIL-STD-202,
Method 208
Mounting position: Any
Mounting torque: 5 in. lb. Max.
Weight: 0.15 ounce, 4.0 grams
0.087(2.2)
0.070(1.8)
0.044(1.1)
0.035(0.9)
0.304(7.7)
0.288(7.3)
GBJ
0.996(25.3)
0.972(24.7)
Unit: inch ( mm )
0.189(4.8)
0.173(4.4)
0.150(3.8)
0.133(3.4)
0.115(2.9)
0.098(2.5)
0.304(7.7)
0.288(7.3)
0.304(7.7)
0.288(7.3)
0.032(0.8)
0.024(0.6)
MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS
Rating at 25°Cambient temperature unless otherwise specified. Resistive or inductive load, 60Hz.
For Capacitive load derate current by 20%.
Maximum Recurrent Peak Reverse Voltage
Maximum RMS Input Voltage
Maximum DC Blocking Voltage
Maximum Average Forward T_C=100°C
Rectified Output Current
I²t Rating for fusing ( t<8.3ms)
Peak Forward Surge Current single sine-wave superimposed on rated load
(JEDEC method)
Maximum Instantaneous Forward Voltage Drop per element at 2.0A
Maximum Reverse Leakage at rated T_A=25°
CDc Blocking Voltage per element T_C=100°C
Typical Thermal Resistance per leg(Note 2) RθJA
Typical Thermal Resistance per leg(Note 3) RθJC
Operating and Storage Temperature Range, TJ,TSTG
GBJ4A
50
GBJ4B
100
GBJ4D
200
35
70
140
50
100
200
GBJ4G GBJ4J
400
600
280
420
400
600
GBJ4K
800
560
800
4.0
UNIT
V
V
V
A
127
A²sec
150
1.0
5
500
8.6
3.1
-55 to +150
Apk
Vpk
µA
µA
°C / W
°C / W
°C
NOTES:
1. Recommended mounting position is to bolt down on heatsink with silicone thermal compound for maximum heat transfer with #6 screw.
2. Units Mounted in free air, no heatsink, P.C.B at 0.375"(9.5mm) lead length with 0.5 x 0.5"(12 x 12mm)copper pads.
3. Units Mounted on a 2.6 x 1.4" x 0.06" thick ( 6.5 x 3.5 x 0.15cm) AL plate.
DATE : OCT.08.2002
PAGE . 1