GBJ10A Datasheet, PDF (1/2 Pages) Pan Jit International Inc. – GLASS PASSIVATED SINGLE-PHASE BRIDGE RECTIFIER(VOLTAGE - 50 to 800 Volts CURRENT - 10.0 Amperes)

DATA SHEET
GBJ10A~GBJ10K
GLASS PASSIVATED SINGLE-PHASE BRIDGE RECTIFIER
VOLTAGE - 50 to 800 Volts CURRENT - 10.0 Amperes
FEATURES
• Plastic material has Underwriters Laboratory
Flammability Classification 94V-O
• Ideal for printed circuit board
• Reliable low cost construction utilizing molded plastic technique
• Surge overload rating: 200 Amperes peak
• High temperature soldering guaranteed:
260°C/10 seconds/.375"(9.5mm) lead length at 5 lbs. (2.3kg) tension
MECHANICAL DATA
Case: Reliable low cost construction utilizing
molded plastic technique
Terminals: Leads solderable per MIL-STD-202,
Method 208
Mounting position: Any
Mounting torque: 5 in. lb. Max.
Weight: 0.15 ounce, 4.0 grams
0.087(2.2)
0.070(1.8)
0.044(1.1)
0.035(0.9)
0.304(7.7)
0.288(7.3)
GBJ
0.996(25.3)
0.972(24.7)
Unit: inch ( mm )
0.189(4.8)
0.173(4.4)
0.150(3.8)
0.133(3.4)
0.115(2.9)
0.098(2.5)
0.304(7.7)
0.288(7.3)
0.304(7.7)
0.288(7.3)
0.032(0.8)
0.024(0.6)
MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS
Rating at 25°Cambient temperature unless otherwise specified. Resistive or inductive load, 60Hz.
For Capacitive load derate current by 20%.
Maximum Recurrent Peak Reverse Voltage
Maximum RMS Input Voltage
Maximum DC Blocking Voltage
GBJ10A GBJ10B GBJ10D GBJ10G GBJ10J _GBJ10K
50
100
200
400
600
800
35
70
140
280
420
560
50
100
200
400
600
800
Maximum Average Forward T_C=100°C
Rectified Output Current TA= 45°C
I²t Rating for fusing ( t<8.3ms)
Peak Forward Surge Current single sine-wave superimposed on rated load
(JEDEC method)
10.0
8.0
166
200
Maximum Instantaneous Forward Voltage Drop per element at 5.0A
1.0
Maximum Reverse Leakage at rated T_A=25°
5
CDc Blocking Voltage per element T_C=100°C
500
Typical Thermal Resistance per leg(Note 2) RθJA
18.0
Typical Thermal Resistance per leg(Note 3) RθJC
3.0
Operating and Storage Temperature Range, TJ,TSTG
-55 to +150
UNIT
V
V
V
A
A²sec
Apk
Vpk
µA
µA
°C / W
°C / W
°C
NOTES:
1. Recommended mounting position is to bolt down on heatsink with silicone thermal compound for maximum heat transfer with #6 screw.
2. Units Mounted in free air, no heatsink, P.C.B at 0.375"(9.5mm) lead length with 0.5 x 0.5"(12 x 12mm)copper pads.
3. Units Mounted on a 3.0 x 3.0" x 0.11" thick ( 7.5 x 7.5 x 0.3cm) AL plate.
DATE : AUG.29.2002
PAGE . 1