HE Datasheet, PDF (7/7 Pages) Panasonic Battery Group – HE RELAYS

2 Form A
CAD Data
MOUNTING METHOD
1. Plug-in type
M4 screw
Washer
Faston No. 250
External dimensions
Single side stable type
M4.0
M.157
51.0
2.008
40.0
1.575
36.4
1.433
14.4
.567
2-4.5 dia.
2-.177 dia.
M3.5
M.138
R4
R.157
33.5
1.319
50.0
1.969
17.5
.689
21.5
.846
16.5
.650
7.5
.295
HE
Schematic (Bottom view)
Single side stable type
12
34
6
5
Panel cutout
2-4.5±0.1 dia.
2-.177±.004 dia.
40±0.1
1.575±.004
Tolerance: ±0.1 ±.004
44.5
1.752
3.5
.138
0.8
.031
General tolerance: ±0.3 ±.012
2. Screw terminal type
M4 screw
Washer
3. Allowable installation wiring size for
screw terminal types and terminal
sockets
Due to the UP terminals, it is possible to
either directly connect the wires or use
crimped terminal.
SAFETY STANDARDS
Item
1 Form A
2 Form A
UL/C-UL (Recognized)
File No. Contact rating
E43028
30A 277V AC
30A 30V DC
1.5HP 125V AC
3HP 250V AC
E43028
25A 277V AC
25A 30V DC
1HP 125V AC
2HP 250V AC
CSA (Certified)
File No. Contact rating
LR26550
etc.
30A 277V AC
30A 30V DC
1.5HP 125V AC
3HP 250V AC
LR26550
etc.
25A 277V AC
25A 30V DC
1HP 125V AC
2HP 250V AC
File No.
40006681
VDE (Certified)
Contact rating
30A 250V AC (cosφ=1.0)
30A 250V AC (cosφ=0.4)
5A 110V DC (0ms)
40006681 25A 250V AC (cosφ=1.0)
25A 250V AC (cosφ=0.4)
5A 110V DC (0ms)
TV rating (UL/CSA)
File No. Rating
UL
E43028
TV-15
File No.
B 11 04
13461 293
TÜV (Certified)
Rating
30A 250V AC (cosφ=1.0)
30A 250V AC (cosφ=0.4)
8A 110V DC (0ms)
UL
E43028
TV-10
B 11 04 25A 250V AC (cosφ=1.0)
13461 293 25A 250V AC (cosφ=0.4)
8A 110V DC (0ms)
NOTES
1. The dust cover should not be removed
since doing so may alter the
characteristics.
2. Avoid use under severe environmental
conditions, such as high humidity, organic
gas or in dust, oily locations and locations
subjected to extremely frequent shock or
vibrations.
3. When mounting, use spring washers.
Optimum fastening torque ranges from
49 to 68.6 N⋅m (5 to 7 kgf·cm).
4. Firmly insert the receptacles so that
there is no slack or looseness. To remove
a receptacle, 19.6 to 39.2 N (2 to 4 kg) of
pulling strength is required. Do not
remove more than one receptacle at one
time. Always remove one receptacle at a
time and pull it straight outwards.
5. When using the AC type, the operate
time due to the in-rush phase is 20 ms or
more. Therefore, it is necessary for you to
verify the characteristics for your actual
circuit.
6. When using the push-on blocks for the
screw terminal type, use crimped
terminals and tighten the screw-down
terminals to the torque below.
M4.5 screw:
147 to 166.6 N⋅cm (15 to 17 kgf·cm)
M4 screw:
117.6 to 137 N·cm (12 to 14 kgf·cm)
M3.5 screw:
78.4 to 98 N·cm (8 to 10 kgf·cm)
For Cautions for Use.
ASCTB183E 201202-T
Panasonic Corporation Automation Controls Business Unit industrial.panasonic.com/ac/e/