EEU-FR1V821L Datasheet, PDF (1/5 Pages) Panasonic Battery Group – Aluminum Electrolytic Capacitors/ FR

Aluminum Electrolytic Capacitors/ FR
Radial Lead Type
Series: _FR Type: _A
■ Features
● Low ESR (Same as FM Series)
● Endurance : 5000 h to 10000 h at +105 °C
● RoHS directive compliant
■ Attention
Not applicable for automotive
■ Country of origin
Malaysia
■ Specifications
Category Temp. Range
Rated W.V. Range
Nominal Cap. Range
Capacitance Tolerance
DC Leakage Current
tan d
Endurance
Shelf Life
–40 °C to +105 °C
6.3 V.DC to 63 V.DC
4.7 μF to 8200 μF
±20 % (120 Hz/+20 °C)
W.V.
tan d
6.3
0.22
I < 0.01 CV (μA) After 2 minutes
10 16 25 35 50
0.19 0.16 0.14 0.12 0.10
63
0.09
(120 Hz/+20 °C)
Add 0.02 per 1000 μF for products of 1000 μF or more.
After following life test with DC voltage and +105 °C±2 °C ripple current value applied. (The sum
of DC and ripple peak voltage shall not exceed the rated working voltage) when the capacitors
are restored to 20 °C, the capacitors shall meet the limits specified below.
Duration
05×11/ 06.3×11.2 : 5000 hours
08×11.5/ 010×12.5 : 6000 hours (✽ Only EEUFR1V331U (010×12.5) 5000 hours)
08×15/ 010×16 : 8000 hours, 08×20 : 9000 hours
010×20 to 010×25/ 012.5×20 to 012.5×35/ 016×20 to 016×25 : 10000 hours
Capacitance change ±25 % of initial measured value (6.3 V to 10 V : ±30 %)
tan d
< 200 % of initial specified value
DC leakage current < initial specified value
After storage for 1000 hours at +105 °C±2 °C with no voltage applied and then being stabilized
at +20 °C, capacitors shall meet the limits specified in Endurance. (With voltage treatment)
■ Frequency correction factor for ripple current
W.V.(V.DC)
6.3 to 63
Cap (μF)
4.7 to
47 to
390 to
1200 to
33
330
1000
8200
60
0.45
0.60
0.65
0.75
■ Dimensions in mm (not to scale)
Pressure relief
06.3
Sleeve
+
–
Body Dia. 0D
Body Length L
Lead Dia. 0d
Lead space F
L⁼
= _{L16 : L±1.5}
L20 : L±2.0
5
—
0.5
2.0
14 min. 3 min.
6.3
8
—
—
0.5
0.6
2.5
3.5
Frequency (Hz)
120
1k
10 k
0.55
0.75
0.90
0.70
0.85
0.95
0.75
0.90
0.98
0.80
0.95
1.00

08
010
0D±0.5
0D±0.5
10
12.5
—
12.5 to 25 30 to 35
0.6
0.6
0.8
5.0
5.0
100 k
1.00
1.00
1.00
1.00
(Unit : mm)
16
—
0.8
7.5
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
05 May. 2014
– EEE-82 –