ECJ-2VC1H221J Datasheet, PDF (4/12 Pages) Panasonic Semiconductor – Multilayer Ceramic Capacitors (For General Electronic Equipment)

Multilayer Ceramic Capacitors(For General Usage)
Item
Bending
Strength
Class 1
Specification
Class 2
Test Method
Appearance:
No mechanical damage
Capacitance change:
Within ±5 % or ±0.5 pF
whichever is larger.
Appearance:
Bending value:1 mm
No mechanical damage Bending speed:1 mm/
Capacitance change:
Temp. Char.
20
B, X7R, X5R : within ±12.5 %
F ,Y5V
: within ±30 %
R340
45±2
45±2
Unit : mm
Vibration
Proof
Appearance: No mechanical damage.
Capacitance: within the specified tolerance
Q, tan δ: Initial standard value
Total amplitude : 1.5 mm
Vibration frequency : 10 to 55 to 10 Hz
for 1 min.
3 perpendicular directions for 2 hours
each, a total of 6 hours
Resistance
to Soldering
Heat
Appearance:
Appearance:
No mechanical damage
No mechanical damage
Capacitance change:
Capacitance change:
Within ±2.5 % or ±0.25 pF Temp. Char.
whichever is larger.
B, X7R, X5R : within ±7.5 %
Q.tan δ:Initial standard value
F, Y5V
: within ±20 %
IR:Initial standard value
tan δ:Initial standard value
Withstand voltage:
IR:Initial standard value
No dielectric breakdown Withstand voltage:
and/or damage
No dielectric breakdown
and/or damage
Soldering bath method
Preconditioning:Heat treatment/Class 2^(✽1)
Solder temperature:270±5 °C
Dipping period:3.0±0.5 s
Preheat condition:
Order Temp. (°C) Size 0805 max.
1 80 to 100 120 to 180 s
2 150 to 200 120 to 180 s
Recovery (Standard condition):
Class 1:24±2 h
Class 2:48±4 h
Solderability More than 95 % of the soldered area of both terminal
electrodes should be covered with fresh solder.
Soldering bath method
Solder temperature:230±5 °C
Dipping period:4±1 s
Solder:H63A (JIS Z 3282)
Temperature
Cycle
Appearance:
Appearance:
No mechanical damage
No mechanical damage
Capacitance change:
Capacitance change:
Within ±2.5 % or ±0.25 pF Temp. Char.
whichever is larger.
B, X7R, X5R : within ±7.5 %
Q.tan δ:Initial standard value F, Y5V
: within ±20 %
IR:Initial standard value
tan δ:Initial standard value
Withstand voltage:
IR:Initial standard value
No dielectric breakdown Withstand voltage:
and/or damage
No dielectric breakdown
and/or damage
Preconditioning:Heat treatment
(150 °C, 1h) /Class 2
Condition of one cycle
Step 1:Minimum operationing temp.
30±3 min
Step 2:Room temp.
3 min max.
Step 3:Maximum operationing temp.
30±3 min
Step 4:Room temp.
3 min max.
Number of cycles:5 cycles
Recovery (Standard condition)
Class 1:24±2 h
Class 2:48±4 h
Damp Heat Appearance:
(Steady state) No mechanical damage
Capacitance change:
Within ±5 % or ±0.5 pF
whichever is larger.
Q:
C<10 pF:Q >200+10C
10 pF<C<30 pF:Q >275+5C/2
30 pF<C <1000 pF:Q > 350
tan δ:
C>1000 pF:tan δ< 0.004
C:Nominal capacitance in pF
IR:
1000 Mȑ or 50/C (Mȑ)
Whichever is less.
C:Nominal capacitance in µF
Appearance:
Preconditioning:Heat treatment/Class 2^(✽1)
No mechanical damage Temperature:40±2 °C
Capacitance change:
Relative humidity:90 to 95 %
Temp. Char.
Test period:500+24/0 h
B, X7R, X5R: Within ±20 % Recovery (Standard condition)
F, Y5V: Within ±30 %
Class 1:24±2 h
tan δ:
Class 2:48±4 h
Temp. Char.
B, X7R, X5R: 0.25 max.
F, Y5V: 0.3 max.
IR:
1000 Mȑ or 50/C (Mȑ)
Whichever is less.
Note:10/C (Mȑ) min. for DC 10 V max.
C:Nominal capacitance in µF
Please see the technical
specifications for details.
(✽1) Heat treatment: 1 h of heat treatment at 150 +0/-10 °C followed by 48±4 h recovery under standard conditions.
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
00 Sep. 2008
– EC11 –