AN8816SB Datasheet, PDF (3/8 Pages) Panasonic Semiconductor – 4ch. Linear Driver IC for CD/CD-ROM

ICs for CD/CD-ROM Player
AN8816SB
s Absolute Maximum Ratings (Ta=25˚C)
Parameter
Symbol
Rating
Unit
Supply Voltage
VCC
18
V
Supply Current
ICC
mA
Power Dissipation ^Note)
PD
3141
mW
Operating Ambient Temperature
Topr
–30 ~ + 85
˚C
Storage Temperature
Tstg
–55 ~ + 150
˚C
Note) For surface mounting on 100 × 80 × 1.6 mm double face glass epoxy board.
s Recommended Operating Range (Ta=25˚C)
Parameter
Symbol
Range
Operating Supply Voltage Range
SVCC ^Note)
PVCC1, PVCC2
5.5V ~ 14V
Note) Set SVCC to the maximum electric potential.
s Electrical Characteristics (Ta=25˚C)
Parameter
Total Circuit Current
Drivers 1 to 4
Input Offset Voltage
Symbol
Itot
VIOF
Output Offset Voltage
VOOF
Gain
G
Maximum Output Amplitude (+)
VL+
Maximum Output Amplitude (–)
VL–
Threshold H
VPCH
Threshold L
Reset Circuit
Reset Operation Release Supply Voltage
VREF Detection
5V Regulator
VPCL
VRST
VREF
Condition
PVCC1 = PVCC2 = SVCC = 8V
PVCC1 = PVCC2 = SVCC = 8V
RL = 8Ω, RIN = 10kΩ
PVCC1 = PVCC2 = SVCC = 8V
RL = 8Ω, RIN = 10kΩ
PVCC1 = PVCC2 = SVCC = 8V
RL = 8Ω, RIN = 10kΩ
PVCC1 = PVCC2 = SVCC = 8V
RL = 8Ω, RIN = 10kΩ
PVCC1 = PVCC2 = SVCC = 8V
RL = 8Ω, RIN = 10kΩ
PVCC1 = PVCC2 = SVCC = 8V
RL = 8Ω, RIN = 10kΩ
PVCC1 = PVCC2 = SVCC = 8V
RL = 8Ω, RIN = 10kΩ
IIN = 10µA, RIN = 10kΩ
min. typ.
5
10
–10
–50
18
20
4.4
5.0
–5.0
2.0
3.0
3.2
2.0
Output Voltage
Output Load Fluctuation
Supply Voltage Fluctuation
OP Amp.
VREG
DVR
DVV
PVCC1 = PVCC2 = SVCC = 8V
PVCC1 = PVCC2 = SVCC = 8V
PVCC1 = PVCC2 = SVCC
= 8V~12V
4.75
5.0
–50
–5
Input Offset Voltage
Input Bias Current
High Level Output Voltage
Low Level Output Voltage
Output Drive Current Sink
Output Drive Current Source
Heat Protection Circuit
VOF
PVCC1 = PVCC2 = SVCC = 8V
IBOP
PVCC1 = PVCC2 = SVCC = 8V
VOH
PVCC1 = PVCC2 = SVCC = 8V
VOL
PVCC1 = PVCC2 = SVCC = 8V
ISIN
PVCC1 = PVCC2 = SVCC = 8V
ISOU
PVCC1 = PVCC2 = SVCC = 8V
–5
100
6.0
2.0
2.0
Operation Temperature Equilibrium Value ^{Note 1)}
Operation Temperature Hysteresis Width ^{Note 1)}
TTHD
DTTHD
( ) (180)
( ) (45)
Note 1) Characteristic value in parentheses is a reference value for design but not a guaranteed value.
max.
15
10
50
22
–4.4
0.3
3.3
5.25
50
5
5
500
1.7
()
()
Unit
mA
mV
mV
dB
V
V
V
V
V
V
V
mV
mV
mV
nA
V
V
mA
mA
˚C
˚C