AN80L20RMSTX Datasheet, PDF (23/27 Pages) Panasonic Semiconductor – Positive output, low dropout voltage regulator (150 mA type)

AN80LxxRMS Series
s Electrical Characteristics at T_a = 25°C (continued)
• AN80L52RMS (5.2 V type)
Unless otherwise specially provided, shorten each test time (within 10 ms) so that the test is conducted under the condition
that the drift due to the temperature increase in the chip junction part can be neglected. C_IN = 0.1 µF, C_OUT = 10 µF
Parameter
Symbol
Conditions
Min Typ Max Unit
Output voltage
V_OUT V_IN = 6.2 V, I_OUT = 50 mA
5.044 5.2 5.356 V
Line regulation 1
REG_IN1 V_IN = 6.2 V → 14.5 V, I_OUT = 50 mA  10 50 mV
Line regulation 2
REG_IN2 V_IN = 6.2 V → 9 V, I_OUT = 50 mA
 5 20 mV
Load regulation ^*1
Peak output current ^*2
REG_LOA V_IN = 6.2 V, I_OUT = 0 mA → 150 mA  50 150 mV
I_PEAK V_IN = 6.2 V, The output current value 180 240  mA
when V_OUT decreases by 5% from its
value at I_OUT = 50 mA.
Bias current under no load
I_BIAS V_IN = 6.2 V, I_OUT = 0 mA
  350 µA
Bias current fluctuation to load ∆I_BIAS V_IN = 6.2 V, I_OUT = 0 mA → 150 mA  
5
mA
Standby consumption current
I_STB V_IN = 10 V, V_CONT = 0 V
  0.1 µA
Bias current before starting
regulation
I_RUSH V_IN = 4.9 V, I_OUT = 0 mA
 1.5 5 mA
Ripple rejection ratio
Minimum input/
output voltage difference 1
RR 1 V[rms], f = 120 Hz, I_OUT = 10 mA
V_DIF(min)1 V_IN = 4.9 V, I_OUT = 0 mA
56 64  dB
 0.1 0.2 V
Minimum input/
output voltage difference 2
V_DIF(min)2 V_IN = 5.3 V, I_OUT = 150 mA
  0.4 V
Control terminal threshold high voltage V_CONTH V_IN = 6.2 V, I_OUT = 50 mA
Control terminal threshold low voltage V_CONTL V_IN = 6.2 V, I_OUT = 50 mA
Control terminal current
I_CONT V_IN = 6.2 V, I_OUT = 50 mA
V_CONT = 1.8 V
  1.50 V
0.30  
V
  30 µA
Note) _*1: 1.0 Ω
*2: ^{Peak output current: The output current when the output voltage has been decreased by 5% from the value at the time}
when the output current is 50 mA due to the overcurrent protection.
• Design reference data
Note) The following values are typical and not guaranteed values.
Parameter
Symbol
Conditions
Output noise voltage
V_NO
Output voltage tempera- 1 _· dV_OUT
ture coefficient
V_OUT dT
Output rise time ^*
t_ON
10 Hz ≤ f ≤ 100 kHz, I_OUT = 10 mA
V_IN = 6.2 V, I_OUT = 0 mA
−30°C ≤ T_a ≤ +85°C
V_IN = 6.2 V, I_OUT = 50 mA
V_CONT = 0 V → 1.8 V, C_IN = 0.1 µF
C_OUT = 10 µF, V_OUT = 90%
Note) *: Refer to "s Application Notes 3. Output rise-time characteristics".
Min Typ Max Unit
 108  µV
 90  ppm/°C
 0.20  ms
SFF00008DEB
23