MN101C77A Datasheet, PDF (2/4 Pages) Panasonic Semiconductor – MN101C77A

MN101C77A, MN101C77C, MN101C77D, MN101C77F
Time base timer (one-minute count setting)
Clock source................ 1/1 of OSC oscillation clock frequency; 1/1 of XI oscillation clock frequency
Interrupt source ........... 1/128, 1/256, 1/512, 1/1024, 1/8192, 1/32768 of clock source frequency
Watchdog timer
Interrupt source ........... 1/65536, 1/262144, 1/1048576 of system clock frequency
 Serial interface
Serial 0 : synchronous type / UART (full-duplex) × 1
Clock source................ 1/2, 1/4 of system clock frequency; pulse output of timer counter 5; 1/2, 1/4, 1/16, 1/64 of OSC oscillation
clock frequency
Serial 1 : synchronous type / UART (full-duplex) × 1
Clock source................ 1/2, 1/4 of system clock frequency; pulse output of timer counter 4; 1/2, 1/4, 1/16, 1/64 of OSC oscillation
clock frequency
Serial 3 : synchronous type/single-master I²C × 1
Clock source................ 1/2, 1/4 of system clock frequency; pulse output of timer counter 3; 1/2, 1/4, 1/16, 1/32 of OSC oscillation
clock frequency
Serial 4 : I²C slave × 1 (Applicable for I²C high-speed transfer mode, 7 bit/10bit address setting, general call)
 DMA controller
Max. Transfer cycles : 255
Starting factor : external request, various types of interrupt, software
Transfer mode : 1-byte transfer, word transfer, burst transfer
 I/O Pins
I/O
53
Common use , Specified pull-up resistor available, Input/output selectable (bit unit)
 A/D converter
10-bit × 7-ch. (with S/H)
 D/A converter
8-bit × 2-ch. (Serves as AD pin, as well)
 Special Ports
Buzzer output, remote control carrier signal output, high-current drive port
 ROM Correction
Correcting address designation : up to 3 addresses possible
 Electrical Charactreistics (Supply current)
Parameter
Symbol
Condition
Limit
Unit
min typ max
IDD1 fosc = 20 MHz , VDD = 3.3 V, (fs = fosc/2)
6 12 mA
Operating supply current
IDD2 fosc = 8.39 MHz , VDD = 3.3 V, (fs = fosc/2)
3
6 mA
IDD3 fx = 32.768 kHz , VDD = 3.3 V, (fs = fx/2)
40 µA
Supply current at HALT
IDD4 fx = 32.768 kHz , VDD = 3.3 V, Ta = 25°C
IDD5 fx = 32.768 kHz , VDD = 3.3 V
5 10 µA
40 µA
Supply current at STOP
IDD6 VDD = 3.3 V, Ta = 25°C
IDD7 VDD = 3.3 V, Ta = 85°C
2 µA
30 µA
(Ta = –40°C to +85°C , VDD = 1.8 V to 3.6 V , VSS = 0 V)
 Development tools
In-circuit Emulator
PX-ICE101C/D+PX-PRB101C77-TQFP064-P-1010C
PX-ICE101C/D+PX-PRB101C77-LQFP064-P-1414
MAD00038JEM