MN101C66D Datasheet, PDF (2/5 Pages) Panasonic Semiconductor – MN101C66D

MN101C66D, MN101C66G
Timer counter 8 : 16 bit × 1
(square-wave/16-bit PWM output [duty continuous variable], event count, pulse width measurement, inputcapture)
(square-wave/PWM output to large current terminal P53 possible)
Clock source................ 1/1, 1/2, 1/4, 1/16, 1/128 of system clock frequency; 1/1, 1/2, 1/4, 1/16, 1/128 of OSC oscillation clock
frequency; 1/1, 1/2, 1/4, 1/16 of external clock input frequency
Interrupt source ........... coincidence with compare register 8 (2 lines)
Timer counters 7, 8 can be cascade-connected.
(square-wave output, PWM, input capture, pulse width measurement is possible as a 32-bit timer.)
Time base timer (one-minute count setting)
Clock source................ 1/1 of OSC oscillation clock frequency; 1/1 of XI oscillation clock frequency
Interrupt source ........... 1/128, 1/256, 1/512, 1/1024, 1/8192, 1/32768 of clock source frequency
Watchdog timer
Interrupt source ........... 1/65536, 1/262144, 1/1048576 of system clock frequency
 Serial interface
Serial 0 : synchronous type/UART (full-duplex) × 1
Clock source................ 1/2, 1/4 of system clock frequency; pulse output of timer counter 3; 1/2, 1/4, 1/16, 1/64 of OSC oscillation
clock frequency
Serial 2 : synchronous type × 1
Clock source................ 1/2, 1/4 of system clock frequency; pulse output of timer counter 3; 1/2, 1/4, 1/16, 1/32 of OSC oscillation
clock frequency
 I/O Pins
I/O
Input
61
Common use , Specified pull-up resistor available, Input/output selectable (bit unit)
(60) ( ) : LQFP080-P-1414A
4
Common use , Specified pull-up resistor available
(3)
( ) : LQFP080-P-1414A
 A/D converter
10-bit × 8-ch. (with S/H)
 Display control function
LCD
32 segments × 4 commons (static, 1/2, 1/3, or 1/4 duty)
LCD power supply separated from VDD (usable if VLCD ≤VDD)
LCD power shunt resistance contained
 Special Ports
Buzzer output, remote control carrier signal output, high-current drive port
 Electrical Charactreistics (Supply current)
Parameter
Symbol
Condition
Operating supply current
Supply current at HALT
Supply current at STOP
IDD1
IDD2
IDD3
IDD4
IDD5
IDD6
IDD7
fosc = 20 MHz , VDD = 5 V
fosc = 8 MHz , VDD = 5 V
fx = 32 kHz , VDD = 3 V
fx = 32 kHz , VDD = 3 V, Ta = 25°C
fx = 32 kHz , VDD = 3 V , Ta = –40°C to +85°C
VDD = 5 V , Ta = 25°C
VDD = 5 V , Ta = –40°C to +85°C
Limit
Unit
min typ max
25 60 mA
10 25 mA
30 100 µA
4
8 µA
30 µA
2 µA
50 µA
 Development tools
In-circuit Emulator
PX-ICE101C/D+PX-PRB101C66-QFP084-P-1818E-M
PX-ICE101C/D+PX-PRB101C66-LQFP080-P-1414A-M
MAD00017HEM