MN101C62F Datasheet, PDF (2/5 Pages) Panasonic Semiconductor – The lower limit for operation guarantee for flash memory built-in type is 2.5 V

MN101C62D, MN101C62F
Timer Counter
(Continue)
Serial Interface
I/O Pins
I/O
A/D Inputs
Special Ports
Electrical Characteristics
Supply current
Parameter
Operating supply current
Supply current at HALT
Supply current at STOP
MAD00020EEM
Timer counter 7 : 16-bit × 1
(square-wave output, 16-bit PWM output (cycle / duty continuous variable), event count, synchronous output
evevt, pulse width measurement, input capture, generation of real time)
Clock source ····················· 1/1, 1/2, 1/4, 1/16 of system clock frequency; 1/1, 1/2, 1/4, 1/16 of OSC
oscillation clock frequency; 1/1, 1/2, 1/4, 1/16 of external clock input frequency
Interrupt source ················ coincidence with compare register 7 (2 lines)
Watchdog timer
Interrupt source ················ 1/65536, 1/262144, 1/1048576 of system clock frequency
Timer counter 8 : 16-bit × 1
(square-wave output, 16-bit PWM output (cycle / duty continuous variable), event count, synchronous output
evevt, pulse width measurement, input capture, generation of real time)
Clock source ····················· 1/1, 1/2, 1/4, 1/16 of system clock frequency; 1/1, 1/2, 1/4, 1/16 of OSC
oscillation clock frequency; 1/1, 1/2, 1/4, 1/16 of external clock input frequency
Interrupt source ················ coincidence with compare register 7 (2 lines)
Watchdog timer
Interrupt source ················ 1/65536, 1/262144, 1/1048576 of system clock frequency
Serial 0 : synchronous type/UART (full-duplex) × 1
Clock source ····················· 1/2, 1/4 of system clock frequency; pulse output of timer counter 1 or 2;
1/2, 1/4, 1/16, 1/64 of OSC oscillation clock frequency
Serial 1 : synchronous type/UART (full-duplex) × 1
Clock source ····················· 1/2, 1/4 of system clock frequency; pulse output of timer counter 2 or 3;
1/2,1/8 of timer counter 2 output;
1/2, 1/4, 1/16, 1/64 of OSC oscillation clock frequency
Serial 2 : synchronous type / single-master I²C
Clock source ····················· 1/2, 1/4 of system clock frequency; pulse output of timer counter 2 or 3;
1/2, 1/4, 1/8, 1/32 of OSC oscillation clock frequency
68 • Common use • Specified pull-up resistor available • Input/output selectable (bit unit)
10-bit × 8-ch. (with S/H)
Buzzer output, remote control carrier signal output, high-current drive port
Symbol
IDD1
IDD2
IDD3
IDD4
IDD5
IDD6
Condition
fosc = 20 MHz, VDD = 5 V
fx = 32 kHz, VDD = 3 V
fx = 32 kHz, VDD = 3 V, Ta = 25°C
fx = 32 kHz, VDD = 3 V, Ta = 85°C
VDD = 5 V, Ta = 25°C
VDD = 5 V, Ta = 85°C
Limit
Unit
min typ max
18 30 mA
30 60 µA
6
8 µA
30 µA
2 µA
50 µA
See the next page for pin assignment and support tool.
2