EVJ-Y96F03B54 Datasheet, PDF (2/5 Pages) Panasonic Semiconductor – Rotary Potentiometers/EVJC/EVJY

■ Specifications
Classification
Applications
Mechanical
Specifications
Rotary Potentiometers/EVJC/EVJY
Item
Rotation Angle
Rotation Torque
Shaft Stopper Strength
Shaft Pull/Push Strength
12 mm square Two-in-One
300 °
2 mN·m to 20 mN·m
0.5 N·m min.
80 N min.
Shaft Inclination
(Measured at the top of the shaft) ^{0.35 mm max.}
Bushing-Nut Tightening Torque
Nominal Total Resistance
Taper
1 N·m max.
5 kȑ to 500 kȑ (Tolerance ±20 %)
A, B, C, D, G, BH
Power Rating
0.05 W (0 °C to 50 °C)
For potentiometers operating in ambient
temperatures above 50 °C, Rating
should be derated in accordance with
the figure on the right.
Power Derating Curve
100
80
60
40
33
20
0 20 40 60 70
Ambient Temperature(°C)
Electrical
Specifications
Residual Resistance
Type _{For general purpose (tone)}
For volume control
Taper &
Nominal ^{Terminal A, B, D, G}
Total
1 to 2
Resistance
B, C, G
2 to 3
5 kȑ < R < 50 kȑ
25 ȑ max.
50 kȑ < R < 250 kȑ
25 ȑ max.
250 kȑ < R < 500 kȑ 100 ȑ max.
A, D
C
A, B, D A, B, D
C
C
2 to 3 1 to 2 1 to 2 2 to 3 1 to 2 2 to 3
25 ȑ max.
50 ȑ max.
100 ȑ max.
15 ȑ max.
15 ȑ max.
50 ȑ max.
25 ȑ max.
50 ȑ max.
100 ȑ max.
20 ȑ max.
20 ȑ max.
50 ȑ max.
Maximum Attenuation
(for volume control,
taper A, B, D)
Nominal total resistance
5 kȑ < R < 10 kȑ
10 kȑ < R < 50 kȑ
50 kȑ < R < 100 kȑ
100 kȑ < R
Max. Attenuation
–65 dB max.
–72 dB max.
–82 dB max.
–92 dB max.
Insertion loss
0.1 dB max.
Tracking
For volume control within
±3 dB at –40 to 0 dB
For Tone control within
±3 dB at midpoint
Insulation Resistance
100 Mȑ min. at 250 Vdc
Dielectric Withstand Voltage 300 Vac for 1 minute
Noise Level
47 mV max.
Apply 20 V (When Voltage Rating < 20 V, use the rated voltage.)
Rotate shaft at 30 r/min.
Endurance
Operating Life ✽1
Minimum Quantity/Packing Unit ✽2
Packing Unit ✽2
✽1 : No direct current should be applied.
✽2 : With bushing : L=L+7.5 mm
15000 cycles min.
80 pcs. (Tray Pack)
60 pcs. (Tray Pack)
800 pcs.
600 pcs.
L<20.0 mm
L>20.0 mm
L<20.0 mm
L>20.0 mm
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
Dec. 2005