ALQ112 Datasheet, PDF (2/6 Pages) Panasonic Semiconductor – 1 Form A/1 Form C 10A Small power relays

LQ (ALQ)
RATING
1. Coil data
Contact Nominal coil
arrangement voltage
1 Form A
1 Form C
5V DC
6V DC
9V DC
12V DC
18V DC
24V DC
5V DC
6V DC
9V DC
12V DC
18V DC
24V DC
Pick-up voltage
(at 20°C 68°F)
75%V or less of
nominal voltage
(Initial)
75%V or less of
nominal voltage
(Initial)
Drop-out voltage
(at 20°C 68°F)
5%V or more of
nominal voltage
(Initial)
5%V or more of
nominal voltage
(Initial)
Nominal operating
current
[±10%] (at 20°C 68°F)
40.0mA
33.3mA
22.2mA
16.7mA
11.1mA
8.3mA
80.0mA
66.7mA
44.4mA
33.3mA
22.2mA
16.7mA
Coil resistance
[±10%] (at 20°C 68°F)
125 Ω
180 Ω
405 Ω
720 Ω
1,620 Ω
2,880 Ω
62.5Ω
90 Ω
202.5Ω
360 Ω
810 Ω
1,440 Ω
Nominal operating
power
(at 20°C 68°F)
200mW
400mW
Max. applied voltage
180% of nominal voltage
(at 20°C 68°F)
130% of nominal voltage
(at 85°C 185°F)*⁴
150% of nominal voltage
(at 20°C 68°F)
110% of nominal voltage
(at 85°C 185°F)*⁴
2. Specifications
Characteristics
Item
Specifications
Contact
Arrangement
Contact resistance (Initial)
Contact material
1 Form A
1 Form C
Max. 100mΩ (By voltage drop 6 V DC 1 A)
AgNi type
Nominal switching capacity (resistive load)
5 A 30 V DC, 10 A 125 V AC, 5 A 250 V AC
N.O. side:
10 A 125 V AC, 5 A 250 V AC, 5 A 30 V DC
N.C. side:
3 A 125 V AC, 2 A 250 V AC, 1 A 30 V DC
Rating
Max. switching power (resistive load)
150 W, 1,250 VA
N.O. side: 150 W, 1,250 VA
N.C. side: 30 W, 500 VA
Max. switching voltage
250 V AC
Max. switching current
N.O.: 10 A (125V AC), N.C.: 3 A (125V AC)
Nominal operating power
200 mW
400 mW
Min. switching capacity (reference value)*¹
Insulation resistance (Initial)
100 mA, 5 V DC
Min. 1,000 MΩ (at 500 V DC) Measurement at same location as “Breakdown voltage” section.
Electrical
characteristics
Mechanical
characteristics
Breakdown voltage ^{Between open contacts}
(Initial)
Between contact and coil
Temperature rise (coil)*⁴
Surge breakdown voltage*²
(Between contact and coil)
Operate time (at nominal voltage) (at 20°C 68°F)
Release time (at nominal voltage) (at 20°C 68°F)
Shock resistance
Vibration resistance
Functional
Destructive
Functional
Destructive
1,000 Vrms for 1 min.
(Detection current: 10 mA)
750 Vrms for 1 min.
(Detection current: 10 mA)
4,000 Vrms for 1 min. (Detection current: 10 mA)
Max. 45°C 113°F (By resistive method, nominal coil voltage applied to the coil; contact carrying
current: 10A, at 85°C 185°F)
8,000 V (Initial)
Max. 20 ms (excluding contact bounce time.) (Initial)
Max. 20 ms (excluding contact bounce time, with diode) (Initial)
1 Form A: 294 m/s², 1 Form C: 196 m/s²
(Half-wave pulse of sine wave: 11 ms; detection time: 10µs.)
980 m/s² (Half-wave pulse of sine wave: 6 ms.)
10 to 55 Hz at double amplitude of 1.6 mm (Detection time: 10µs.)
10 to 55 Hz at double amplitude of 2.0 mm
Expected life
Conditions
Mechanical
Conditions for operation, transport and storage*³
Max. operating speed
Min. 10⁷ (at 180 times/min.)
Ambient temperature: –40°C to +85°C –40°F to +185°F
Humidity: 5 to 85% R.H. (Not freezing and condensing at low temperature)
20 times/min. (at nominal switching capacity)
Unit weight
Approx. 7 g .25 oz
* Specifications will vary with foreign standards certification ratings.
Notes: *1. This value can change due to the switching frequency, environmental conditions, and desired reliability level, therefore it is recommended to check this with the
actual load.
*2. Wave is standard shock voltage of ±1.2×50µs according to JEC-212-1981
*3. The upper limit of the ambient temperature is the maximum temperature that can satisfy the coil temperature rise value. Refer to Usage, transport and storage
conditions in NOTES.
*4. When using relays in a high ambient temperature, consider the pick-up voltage rise due to the high temperature (a rise of approx. 0.4% V for each 1°C 33.8°F with
20°C 68°F as a reference) and use a coil impressed voltage that is within the maximum applied voltage range.
Panasonic Corporation Automation Controls Business Unit industrial.panasonic.com/ac/e/
ASCTB92E 201206-T