MN101C93 Datasheet, PDF (1/3 Pages) Panasonic Semiconductor – MN101C93 Series

MN101C93 Series
Type
Internal ROM type
ROM (byte)
RAM (byte)
Package (Lead-free)
Minimum Instruction
Execution Time
MN101C93K
MN101CF93K
Mask ROM
FLASH
224K
6K
LQFP100-P-1414
0.125 µs (at 3.0 V to 3.6 V, 8 MHz)
62.5 µs (at 3.0 V to 3.6 V, 32 kHz)
0.167 µs (at 3.0 V to 3.6 V, 6 MHz)
62.5 µs (at 3.0 V to 3.6 V, 32 kHz)
 Interrupts
RESET. Watchdog. External 0 to 5. External 6 (key interrupt dedicated). Timer 0 to 3. Timer 6. Timer 7 (2 systems). Timer 8 (2 systems).
Time base. Serial 0 (2 systems). Serial 1 (2 systems). Serial 3 (1 systems). A/D conversion finish. Automatic transfer finish. USB
interrupts
 Timer Counter
8-bit timer × 5
Timer 0 ..................Square-wave/8-bit PWM output. Event count. Remote control carrier output. Simple pulse width measurement.
Added pulse (2-bit) type PWM output. Square-wave/PWM output to large current terminal PC3 possible
Timer 1 ..................Square-wave output. Event count. Serial transfer clock output. Synchronous output event
Timer 2 ..................Square-wave output. Added pulse (2-bit) type PWM output. PWM output. Serial transfer clock output. Event
count. Synchronous output event. Simple pulse width measurement. Square-wave/PWM output to large current
terminal PC5 possible
Timer 3 ..................Square-wave output. Event count. Serial transfer clock output
Timer 6 ..................8-bit freerun timer
Timer 0, 1 can be cascade-connected
Timer 2, 3 can be cascade-connected
16-bit timer × 2
Timer 7 ..................Square-wave output. 16-bit PWM output (cycle/duty continuous variable). Event count. Synchronous output
event. Pulse width measurement. Input capture. Real time output control. High performance IGBT output. Square-
wave/PWM output to large current terminal PC4 possible
Timer 8 ..................Square-wave/16-bit PWM output (duty continuous variable). Event count. Pulse width measurement. Input
capture. Square-wave/PWM output to large current terminal PC6 possible
Timer 7, 8 can be cascade-connected: Square-wave output, PWM is possible as a 32-bit timer
Time base timer: One-minute count setting
Watchdog timer × 1
 Serial interface
Synchronous type/UART (full-duplex) × 2: Serial 0, 1
Synchronous type/Single-master I²C × 1: Serial 3
 DMA controller
Maximum transfer cycles: 255
Starting factor: External request. Various types of interrupt. Software
Transfer mode: 1-byte transfer. Word transfer. Burst transfer
 USB Functions
Conforms to USB 1.1: Full-speed (12 Mbps) supported
USB transceiver built-in. 5 end points (FIFO built-in independently)
FIFO size: EP0 = 16 bytes. EP1 = 128 bytes. EP2 = 128 bytes. EP3 = 64 bytes. EP4 = 64 bytes
EP0: Control transfer. IN/OUT (two ways)
EP1 to EP4: Interrupt/Bulk/Isochronous transfer supported. Settable to IN or OUT. Double Buffering function supported
When the MAXP size is set to a half or less of the MAXFIFO size for each EP, the Double Buffering function is made valid
automatically
 I/O Pins
I/O
84 : Common use. Specified pull-up resistor available. Input/output selectable (bit unit)
 A/D converter
10-bit × 12 channels (with S/H)
MAD00056GEM