EEV-FK1H221P Datasheet, PDF (1/7 Pages) Panasonic Semiconductor – Aluminum Electrolytic Capacitor/FK series

Aluminum Electrolytic Capacitor/FK series
Surface Mount Type
Series: _FK
n Features
Type : V
Country of Origin
Endurance: 2000 to 5000h at105°C
Low impedance (40 to 60% less than FCseries)
Miniaturization(30 to 50% less than FC series)
Vibration-proof product is available upon request.(f8 ^<= )
Japan
n Specifications
Category temp. range
-55 to +105°C
Rated W.V. Range
6.3 to 100V .DC
Nominal Cap. Range
Capacitance Tolerance
DC Leakage Current
tan d
3.3 to 6800 µ F
±20 % (120Hz/+20°C)
I ^<= 0.01CV or 3(µA) After 2 minutes application of rated working voltage at +20°C. (Whichever is greater)
Please see the attached standard products list
Characteristics
at Low Temperature
Endurance
Shelf Life
Resistance to
Soldering Heat
W.V. (V)
6.3 10 16 25 35 50 63 80 100
Z(-25°C) / Z(+20°C) 2
2
2
2
2 2222
(Impedance ratio
Z(-40 °C)/ Z(+20 °C) 3
3
3
3
3
3333
at 120 Hz)
Z(-55°C)/ Z(+20 °C) 4
4
4
3
3 3333
After the life with DC rated working voltage at +105±2°C for 2000 hours ( _=> dia.12.5 and suffix
“G” in dia.8 to 10mm are 5000 hours)the capacitors shall meet the limits specified below.
post-test requirement at +20°C.
Capacitance change ±30% of initial measured value (Suffix “G” is 35%)
tan d
<= _{200 % of initial specified value (Suffix “G” is 300%)}
DC leakage current ^<= initial specified value
After storage for 1000hours at +105±2 °C with no voltage applied and then being stabilized
at +20°C, capacitors shall meet the limits specified in Endurance.(With voltage treatment)
After reflow soldering ( Refer to the "Application Guide" for recommended temperature profile.)
and then being stabilized at +20°C, capacitor shall meet the following limits.
Capacitance change ±10% of initial measured value
D.F. tan d
<=_{ initial specified value}
DC leakage current ^<= initial specified value
n Marking
n Dimensions in mm (not to scale)
Example.16V10µF
Marking color : BLACK
W.V. code
0.3 max
A± 0.2
( ) reference size
Capacitance
Negative polarity
10
(µF)
marking
C FK
Series
identification
B~G=L ±0.3
H~K=L±0.5
w
Lot number
(=>f12.5)
W.V. code
Capacitance
(µF)
Negative polarity
marking
FK
Series
identification
W.V. code
V
Code
V
Code
Lot number
6.3 10 16 25 35
j A CEV
50 63 80 100
H J K 2A
Size
code
D
L A,B H max. I
W
P
K
B 4.0 _5.8 4.3 5.5 _1.8 0.65±0.1 1.0 _{0.35 -0.20 to +0.15}
C 5.0 _5.8 5.3 6.5 _2.2 0.65±0.1 1.5 _0.35 -0.20 to +0.15
D 6.3 _5.8 6.6 7.8 _2.6 0.65±0.1 1.8 _0.35 -0.20 to +0.15
D8 6.3 _7.7 6.6 7.8 _2.6 0.65±0.1 1.8 _0.35 -0.20 to +0.15
E 8.0 _6.2 8.3 9.5 _3.4 0.65±0.1 2.2 _0.35 -0.20 to +0.15
F 8.0 _10.2 8.3 10.0 _3.4 0.90±0.2 3.1 _0.70 ±0.20
G 10.0 _10.2 10.3 12.0 _3.5 0.90±0.2 4.6 _0.70 ±0.20
H13 12.5 _13.5 13.5 15.0 _4.7 0.90±0.3 4.4 _0.70 ±0.30
J16 16.0 _16.5 17.0 19.0 _5.5 1.20±0.3 6.7 _0.70 ±0.30
K16 18.0 _16.5 19.0 21.0 _6.7 1.20±0.3 6.7 _0.70 ±0.30
Design and specifications are subject to change without notice. Ask factory for technical specifications before purchase and/or use.
Whenever a doubt about safety arises from this product, please contact us immediately for technical consultation.