EEUTP1E332 Datasheet, PDF (1/2 Pages) Panasonic Semiconductor – Aluminum Electrolytic Capacitors

Radial Lead Type
Series: _TP Type: _A
Aluminum Electrolytic Capacitors/ TP
■ Features
● Endurance: 125 °C 2000 h to 5000 h or 135 °C 1000 h to 2000 h
● Smaller than series TA
● High ripple current (at high frequency) : 20 to 40% higher than TA series
● RoHS directive compliant
■ Specifications
Category Temp. Range
Rated W.V. Range
Nominal Cap. Range
Capacitance Tolerance
DC Leakage Current
tan δ
Endurance 1
Endurance 2
–40 °C to + 135 °C
25 V .DC to 35 V .DC
100 µF to 5100 µF
±20 % (120 Hz/+20 °C)
I < 0.01 CV or 3 (µA) After 2 minutes (Whichever is greater)
W.V.(V)
tan δ
25 35
0.14 0.12 ^{(120Hz / +20 °C)}
For capacitance value > 1000 µF , add 0.02 per every 1000 µF.
After following life test with DC voltage and +125 °C±2 °C ripple current value applied. (The sum
of DC and ripple peak voltage shall not exceed the rated working voltage) when the capacitors
are restored to 20 °C, the capacitors shall meet the limits specified below.
Duration
φ8 : 2000 hours, φ10 : 3000 hours, φ12.5 : 4000 hours, φ16 to φ18 : 5000 hours
Capacitance change ±30% of initial measured value
tan δ
< 300 % of initial specified value
DC leakage current < initial specified value
After following life test with DC voltage and +135 °C±2 °C ripple current value applied. (The sum
of DC and ripple peak voltage shall not exceed the rated working voltage) when the capacitors
are restored to 20 °C, the capacitors shall meet the limits specified below.
Duration
φ8 : 1000 hours, φ10 to φ18 : 2000 hours
Capacitance change ±30% of initial measured value
tan δ
< 300 % of initial specified value
DC leakage current < initial specified value
Shelf Life 1
After storage for 1000 hours at +125 °C±2 °C with no voltage applied and then being stabilized
at +20 °C, capacitors shall meet the limits specified in Endurance. (With voltage treatment)
Shelf Life 2
After storage for 1000 hours at +135 °C±2 °C with no voltage applied and then being stabilized
at +20 °C, capacitors shall meet the limits specified in Endurance. (With voltage treatment)
■ Frequency correction factor for ripple current
W.V.
(V.DC)
Cap. (µF)
60
to 330
0.55
25 to 35
390 to 1000
0.70
1200 to
0.75
120
0.65
0.75
0.80
Frequency (Hz)
1k
0.85
0.90
0.90
10 k
0.90
0.95
0.95
100 k
1.00
1.00
1.00
■ Dimensions in mm (not to scale)
Sleeve
φd±0.05
φ8
Pressure relief
+
–
[mm]
φ10<
Body Dia. φD
Lead Dia. φd
Lead space F
✽L
✽ L<16 : L±1.5
L>20 : L±2.0
8
0.6
3.5
14 min. 3 min.
10
0.6
5.0
φD±0.5
12.5
0.6
5.0
φD±0.5
16
0.8
7.5
(mm)
18
0.8
7.5
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
00 Jan. 2011