EEHZK1E271V Datasheet, PDF (1/2 Pages) Panasonic Semiconductor – Conductive Polymer Hybrid Aluminum Electrolytic Capacitors

Conductive Polymer Hybrid Aluminum Electrolytic Capacitors
Surface Mount Type
Series : ZK Type : V
High temperature Lead-Free reflow
Features
● _{High capacitance and High ripple current compared with ZC series}
● _{Endurance : 4000 h at 125 °C (High temperature / Long life)}
● _{Low ESR (85 % over, Lower ESR than Current V-TP), Low LC (0.01 CV or 3 μF)}
● _{Equivalent to conductive polymer type Aluminum Electrolytic Capacitor}
(There are little characteristics change by temperature and frequency)
● _{Vibration-proof product is available upon request. (08 mm and larger)}
● _{AEC-Q200 compliant}
● _{RoHS directive compliant}
Specifications
Size code
C
D
D8
F
G
Category temp. range
–55 °C to +125 °C
Rated voltage range
25 V.DC to 35 V.DC
Nominal cap.range
33 μF to 47 μF
56 μF to 68 μF 100 μF to 150 μF 180 μF to 270 μF 330 μF to 470 μF
Capacitance tolerance
±20 % (120 Hz/+20 °C)
DC leakage current
I < 0.01 CV or 3 (μA) After 2 minutes (whichever is greater)
Dissipation factor (tan d)
Please see the attached standard products list
125 °C, 4000 h, apply the rated ripple current without exceeding the rated voltage
Capacitance change Within ±30% of the initial value
tan d
< 200 % of the initial limit
Endurance
E. S. R.
< 200 % of the initial limit
DC leakage current Within the initial limit
Size code
ESR after Endurance
(Ω/100 kHz) (–40 °C)
C
D
D8
F
G
2.0
1.4
0.8
0.4
0.3
Shelf life
After storage for 1000 hours at +125 °C±2 °C with no voltage applied and then being stabilized at +20 °C,
capacitors shall meet the limits specified in Endurance. (With voltage treatment)
85 °C, 85 % to 90 %, 2000 h, rated voltage applied
Capacitance change Within ±30 % of the initial value
Damp heat (Load)
tan d
< 200 % of the initial limit
E. S. R.
< 200 % of the initial limit
DC leakage current Within the initial limit
After reflow soldering and then being stabilized at +20 °C, capacitors shall meet the following limits.
Resistance to
soldering heat
Capacitance change Within ±10% of the initial value
tan d
Within the initial limit
DC leakage current Within the initial limit
Marking
Example : 25 V.DC 47 μF Marking color : BLACK
Negative polarity marking (–)
47
E ZK
Capacitance (μF)
Series identification
Lot number
Rated voltage mark
Rated voltage mark
E
25 V.DC
V
35 V.DC
Dimensions (not to scale)
0.3 max.
A±0.2
–
+
L
W
Pressure relief (010 and larger)
( ) Reference size
(Unit : mm)
Size
code
D
L A, B H
I
W
P
C 5.0 5.8±0.3 5.3 6.5 max. 2.2 0.65±0.1 1.5
D 6.3 5.8±0.3 6.6 7.8 max. 2.6 0.65±0.1 1.8
D8 6.3 7.7±0.3 6.6 7.8 max. 2.6 0.65±0.1 1.8
F 8.0 10.2±0.3 8.3 10.0 max. 3.4 0.90±0.2 3.1
G 10.0 10.2±0.3 10.3 12.0 max. 3.5 0.90±0.2 4.6
K
0.35
+
-
0.15
0.20
0.35
+
-
0.15
0.20
0.35
+
-
0.15
0.20
0.70±0.2
0.70±0.2
· The dimensions of the vibration-proof products, please refer to the page of
the mounting specification.
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
01 Nov. 2016