|
EEHZE1E221P Datasheet, PDF (1/2 Pages) Panasonic Semiconductor – Conductive Polymer Hybrid Aluminum Electrolytic Capacitors | |||
|
Conductive Polymer Hybrid Aluminum Electrolytic Capacitors
Surface Mount Type
Series : ZE Type : V
High temperature Lead-Free reflow
Features
â Endurance: 2000 h at 145 °C (High temperature / Long life)
â Low ESR and high ripple current (85 % over, Lower ESR than current V-TP)
â High-withstand voltage (25 V.DC to 63 V.DC), Low LC (0.01 CV or 3 μA)
â Equivalent to conductive polymer type aluminum electrolytic capacitor
(There are little characteristics change by temperature and frequency)
â Vibration-proof product is available upon request. (08 mm and larger)
â AEC-Q200 compliant
â RoHS directive compliant
Specifications
Size code
F
G
Category temp. range
â55 °C to +145 °C
Rated voltage range
25 V.DC to 63 V.DC
Nominal cap.range
33 μF to 220 μF
56 μF to 330 μF
Capacitance tolerance
±20 % (120 Hz/+20 °C)
DC leakage current
I < 0.01 CV or 3 (μA) After 2 minutes (whichever is greater)
Dissipation factor (tan d)
Please see the attached standard products list
145 °C, 2000 h, apply the rated ripple current without exceeding the rated voltage
Capacitance change Within ±30% of the initial value
Endurance 1
tan d
< 200 % of the initial limit
E. S. R.
< 200 % of the initial limit
DC leakage current Within the initial limit
135 °C, 4000 h, apply the rated ripple current without exceeding the rated voltage
Capacitance change Within ±30% of the initial value
Endurance 2
tan d
< 200 % of the initial limit
E. S. R.
< 200 % of the initial limit
DC leakage current Within the initial limit
Shelf life
After storage for 1000 hours at +145 °C±2 °C with no voltage applied and then being stabilized at +20 °C,
capacitors shall meet the limits speciï¬ed in Endurance. (With voltage treatment)
85 °C, 85 % to 90 %, 2000 h, rated voltage applied
Capacitance change Within ±30% of the initial value
Damp heat (Load)
tan d
< 200 % of the initial limit
E. S. R.
< 200 % of the initial limit
DC leakage current Within the initial limit
After reï¬ow soldering and then being stabilized at +20 °C, capacitors shall meet the following limits.
Resistance to
soldering heat
Capacitance change Within ±10% of the initial value
tan d
Within the initial limit
DC leakage current Within the initial limit
Marking
Example : 25 V.DC 220 μF Marking color : BLACK
Negative polarity marking (â)
220
E ZE
Capacitance (μF)
Series identiï¬cation
Lot number
Rated voltage mark
E
25 V.DC
V
35 V.DC
Rated voltage mark
H
50 V.DC
J
63 V.DC
Dimensions (not to scale)
0.3 max.
A±0.2
â
+
L
Pressure relief (010 and larger)
Size
code
D
L A, B H
I
F 8.0 10.2±0.3 8.3 10.0 max. 3.4
G 10.0 10.2±0.3 10.3 12.0 max. 3.5
W
( ) Reference size
(Unit : mm)
W
P
K
0.90±0.2 3.1 0.70±0.2
0.90±0.2 4.6 0.70±0.2
· The dimensions of the vibration-proof products, please refer to the page of
the mounting speciï¬cation.
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
00 Mar. 2017
|
▷ |