|
EEH-ZA1J560P Datasheet, PDF (1/2 Pages) Panasonic Semiconductor – Conductive Polymer Hybrid Aluminum Electrolytic Capacitors/ZA | |||
|
Conductive Polymer Hybrid Aluminum Electrolytic Capacitors/ZA
Surface Mount Type
Series: ZA Type: V
High temperature Lead-Free reflow
â Features
â Endurance: 10000 h at 105 °C
â Low ESR and High ripple current
(70 % over, Lower ESR than Current V-FP)
â High voltage (to 80 V)
â Equivalent to conductive polymer type Aluminum Electrolytic Capacitor
(There are little characteristics change by temperature and frequency)
â AEC-Q200 qualiï¬edâ½
â RoHS directive compliant
â Specifications
Category Temp. Range
â55 °C to +105 °C
Rated W.V.Range
25 V.DC to 80 V.DC
Nominal Cap.Range
10 μF to 330 μF
Capacitance Tolerance
±20 % (120 Hz/+20 °C)
DC Leakage Current
I < 0.01 CV or 3 (μA) After 2 minutes (whichever is greater)
tan d
Please see the attached Standard Products list
The capacitor shall be subjected to application of the D.C. voltage with full rated ripple current at +105 °C for 10000
hours. After stabilizing at room temperature(+15 to 35 °C), the capacitor shall not exceed the speciï¬ed limits.
(The sum of DC voltage and ripple peak voltage shall not exceed the rated voltage.)
Capacitance change ±30 % of initial measured value
Endurance
tan d
< 200 % of initial speciï¬ed value
E. S. R.
< 200 % of initial speciï¬ed value
DC leakage current < initial speciï¬ed value
Size Code
ESR after Endurance
(Ω/100 kHz) (â40 °C)
C
D
D8
F
G
2.0
1.4
0.8
0.4
0.3
Shelf Life
After storage for 1000 hours at +105 °C±2 °C with no voltage applied and then being stabilized at +20 °C,
capacitors shall meet the limits speciï¬ed in Endurance. (With voltage treatment)
After reï¬ow soldering and then being stabilized at +20 °C, capacitors shall meet the following limits.
Resistance to
Soldering Heat
Capacitance change
tan d
DC leakage current
±10 % of initial measured value
< initial speciï¬ed value
< initial speciï¬ed value
â Frequency correction factor for ripple current
120
Correction factor
0.10
Frequency (Hz)
1k
10 k
0.30
0.60
100 k to
1.00
â Marking
Example:25 V 33 μF Marking color : BLACK
Negative polarity marking (â)
& ;"
Capacitance (μF)
Series identiï¬cation
Lot number
Rated Voltage Mark
E
25 V
V
35 V
H
50 V
Rated Voltage Mark
J
63 V
K
80 V
â Dimensions in mm (not to scale)
0.3 max.
A±0.2
â
(Unit : mm)
+
L
Pressure Relief (010 and larger)
W
( ) Reference size
Size
code
D
L A, B H
I
C 5.0 5.8±0.3 5.3 6.5 max. 2.2
D 6.3 5.8±0.3 6.6 7.8 max. 2.6
D8 6.3 7.7±0.3 6.6 7.8 max. 2.6
F 8.0 10.2±0.3 8.3 10.0 max. 3.4
G 10.0 10.2±0.3 10.3 12.0 max. 3.5
W
P
0.65±0.1 1.5
0.65±0.1 1.8
0.65±0.1 1.8
0.90±0.2 3.1
0.90±0.2 4.6
K
0.35
+
-
0.15
0.20
0.35
+
-
0.15
0.20
0.35
+
-
0.15
0.20
0.70±0.2
0.70±0.2
â½ This product qualify for AEC-Q200, but it has some deviations.
Design and speciï¬cations are each subject to change without notice. Ask factory for the current technical speciï¬cations before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
02 Mar. 2014
â EEE-2 â
|
▷ |