EEH-ZA1H330XP Datasheet, PDF (1/2 Pages) Panasonic Semiconductor – Conductive Polymer Hybrid Aluminum Electrolytic Capacitors / ZA

Conductive Polymer Hybrid Aluminum Electrolytic Capacitors / ZA
Surface Mount Type
Series: ZA Type: V
High temperature Lead-Free reflow
■ Features
● Endurance: 10000 h at 105 ℃
● Low ESR and High ripple current
(70 % over, Lower ESR than Current V-FP)
● High voltage (to 80V)
● Equivalent to conductive polymer type Aluminum Electrolytic Capacitor
(There are little characteristics change by temperature and frequency)
● Vibration-proof product is available upon request. (φ8 mm and larger)
● AEC-Q200 qualified*
● RoHS directive compliant
■ Specifications
Category Temp.Range
-55 ℃ to +105 ℃
Rated W.V. Range
25 V.DC to 80 V.DC
Nominal Cap. Range
10 μF to 330 μF
CapacitanceTolerance
±20 % (120 Hz/+20 ℃)
DC Leakage Current
l ≦ 0.01 CV or 3 (μA) After 2 minutes (Whichever is greater)
tan δ
Please see the attached Standard Products list
The capacitor shall be subjected to application of the D.C. voltage with full rated ripple current at +105 ℃ for 10000
hours. After stabilizing at room temperature(+15 to 35 ℃), the capacitor shall not exceed the specified limits.
(The sum of DC voltage and ripple peak voltage shall not exceed the rated voltage.)
Capacitance change ±30 % of initial measured value
Endurance
tan δ
E.S.R.
≦ 200 % initial specified value
≦ 200 % initial specified value
DC leakage current ≦ initial specified value
ESR after Endurance
（Ω/100 kHz) (-40℃)
C
2.0
Size Code
D
D8
F
1.4
0.8
0.4
G
0.3
Shelf Life
After storage for 1000 hours at +105 ℃±2 ℃ with no voltage applied and then being stabilized at +20 ℃,
capacitors shall meet the limits specified in Endurance. (With voltage treatment)
After applying rated working voltage for 2000 hours at +85℃±2℃ / 85% to 90%RH and then being stabilized
at +20℃, Capacitors shall meet the following limits.
Damp Heat (Load)
Capacitance change ±30 % of initial measured value
tan δ
≦ 200 % initial specified value
E.S.R.
≦ 200 % initial specified value
DC leakage current ≦ initial specified value
After reflow soldering and then being stabilized at +20 ℃, capacitors shall meet the following limits.
Resistance to
Capacitance change ±10 % of initial measured value
Soldering Heat
tan δ
≦ initial specified value
DC leakage current ≦ initial specified value
■ Marking
Example : 25 V 33 μF　　Marking color : BLACK
Negative polarity marking (－)
33
E ZA
Capacitance (μF)
Series identification
Rated Voltage Mark
Lot number
Rated Voltage Mark
E
25 V
J
63 V
V
35 V
K
80 V
H
50 V
■ Dimensions in mm (not to scale)
0.3max.
A±0.2
(Unit : mm)
L
Pressure Relief (φ10 and
W
( ) Reference
Size
code
D
L
A, B
H
I
C 5.0 5.8±0.3 5.3 6.5 max. 2.2
D 6.3 5.8±0.3 6.6 7.8 max. 2.6
D8 6.3 7.7±0.3 6.6 7.8 max. 2.6
F 8.0 10.2±0.3 8.3 10.0 max. 3.4
G 10.0 10.2±0.3 10.3 12.0 max. 3.5
W
P
0.65±0.1 1.5
0.65±0.1 1.8
0.65±0.1 1.8
0.90±0.2 3.1
0.90±0.2 4.6
K
0.35_-+00..1250
0.35_-+00..1250
0.35_-+00..1250
0.70±0.2
0.70±0.2
＊ This product qualifi for AEC-Q200, but it has some deviations.
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
Oct. 2014
－ EEE-2 －