EEE-TG1E101UP Datasheet, PDF (1/4 Pages) Panasonic Semiconductor – Aluminum Electrolytic Capacitors/ TG

Aluminum Electrolytic Capacitors/ TG
Surface Mount Type
Series: _TG Type: _V
■ Features
● Endurance:125 °C 1000 h to 2000 h
● Miniaturization (40 % less than TA Series)
● Low ESR (Low temp)
● Vibration-proof product is available upon request. (φ8 <)
● RoHS directive compliant (Parts No φ8 to φ10 : EEE✽, φ12.5 to φ18 : EEV✽)
■ Specifications
Category Temp. Range
Rated W.V. Range
Nominal Cap. Range
–40 °C to +125 °C
10 V.DC to 100 V.DC
10 µF to 4700 µF
Capacitance Tolerance
DC Leakage Current
tan δ
Characteristics
at Low Temperature
W.V. (V)
Z(–25 °C)/Z(+20 °C)
Z(–40 °C)/Z(+20 °C)
±20 % (120 Hz/+20 °C)
I < 0.01 CV After 2 minutes
Please see the attached standard products list
10 16 25 35 50 63 80 100
3
2
2
2
2
2
2
2 (Impedance ratio at 120 Hz)
6
4
4
3
3
3
3
3
After applying rated working voltage for 1000 hours (φ8҂6.2), 2000 hours (φ8҂10.2 <) at +125 °C±2 °C and then
being stabilized at +20 °C, capacitors shall meet the following limits.
Endurance
Capacitance change
tan δ
DC leakage current
±30 % of initial measured value (code U : ±35 %)
< 300 % of initial specified value (code U : ±350 %)
< initial specified value
Shelf Life
After storage for 1000 hours at +125 °C±2 °C with no voltage applied and then being stabilized
at +20 °C, capacitors shall meet the limits specified in Endurance (With voltage treatment)
After reflow soldering and then being stabilized at +20 °C, capacitors shall meet the following limits.
Resistance to
Soldering Heat
Capacitance change
tan δ
DC leakage current
±10 % of initial measured value
< initial specified value
< initial specified value
■ Marking
Example : 10 V 100 µF, 10 V 1000 µF
Marking coloc : BLACK
Lead-Free products (< φ10)
Rated Voltage Mark
Negative polarity
marking (–)
100
A TG
Lot number
Capacitance (µF)
Series identification
Mark for Lead-Free
Products Black Dot
(Square)
Lead-Free products (> φ12.5)
Rated Voltage Mark
Negative polarity
marking (–)
1000
A TG
Capacitance (µF)
Series identification
■ Dimensions in mm (not to scale)
0.3 max.
( )reference size
A±0.2
–
L±0.3
✽L±0.5
+
W
Lot number
Rated Voltage Mark
A
10 V
C
16 V
E
25 V
V
35 V
H
50 V
J
63 V
K
80 V
2A
100 V
(mm)
Size
code
E
D L A,B H max. I
W
P
K
8.0 6.2 8.3 9.5 3.4 0.65±0.1 2.2 0.35–0.20 to +0.15
F 8.0 10.2 8.3 10.0 3.4 0.90±0.2 3.1 0.70±0.20
G 10.0 10.2 10.3 12.0 3.5 0.90±0.2 4.6 0.70±0.20
H13^✽ 12.5 13.5 13.5 15.0 4.7 0.90±0.3 4.4 0.70±0.30
J16 ^✽ 16.0 16.5 17.0 19.0 5.5 1.20±0.3 6.7 0.70±0.30
K16^✽ 18.0 16.5 19.0 21.0 6.7 1.20±0.3 6.7 0.70±0.30
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
Apr. 2008