ECWU1C124JC9 Datasheet, PDF (1/3 Pages) Panasonic Semiconductor – Plastic Film Capacitors

Stacked Metallized PEN Film Chip Capacitor
Type: ECWU(C)
Plastic Film Capacitors
Stacked metallized PEN film as dielectric with simple
mold-less construction
I Features
•^{Small in size}
•^{For reflow soldering}
•^{RoHS directive compliant}
IRecommended Applications
•^{General purpose (Coupling, By-pass)}
IExplanation of Part Numbers
1
2
EC
Product code
3
4
WU
Dielectric
&
construction
5
6
Rated voltage
7
8
9
10
11
C
Nominal capacitance Cap. Tol. Suffix
12
Suffix
1C 16 VDC
1H 50 VDC
1 100 VDC
2 250 VDC
J ^±5 %
K ^±10 %
Tape width
9 12 mm
V 16 mm
I Specifications
Category temp.range
(Including temperature-rise on unit surface)
Rated voltage
Capacitance range
Capacitance tolerance
Withstand voltage
Dissipation factor (tan )
Insulation resistance (IR)
16 VDC, 50 VDC : -55 ˚C to +105 ˚C
100 VDC, 250 VDC : -55 ˚C to +125 ˚C
16 VDC, 50 VDC, 100 VDC, 250 VDC
(100 VDC, 250 VDC : Derating of rated voltage by 1.25 %/˚C more than 85 ˚C)
16 VDC
0.12 µF to 0.47 µF (E12)
50 VDC
0.056 µF to 0.22 µF (E12)
100 VDC
0.012 µF to 1.0 µF (E12)
250 VDC
0.0010 µF to 0.12 µF (E12)
16 VDC, 50 VDC ±5 %(J)
100 VDC
±5 %(J), ±10 %(K) (C₌^>0.18 µF : ±10 %(K)only)
250 VDC
±5 %(J), ±10 %(K)
Between terminals: Rated volt. (VDC)✕150 % 60 s
tan ^<₌1.0 %(20 ˚C, 1 kHz)
C^<₌0.33 µF
16 VDC : IR₌^>3000 MΩ · (20 ˚C,10 VDC, 60 s)
50 VDC : IR₌^>3000 MΩ · (20 ˚C,50 VDC, 60 s)
100 VDC, 250 VDC : IR₌^>3000 MΩ · (20 ˚C,100 VDC, 60 s)
C>0.33 µF
16 VDC : IR₌^>1000 MΩ · µF (20 ˚C,10 VDC, 60 s)
100 VDC : IR=>1000 MΩ · µF (20 ˚C,100 VDC, 60 s)
Soldering conditions
Reflow soldering : 240 ˚C max. and 60 s max. at more than 220 ˚C (Temp. at cap. surface)
(Please consult us for Reflow 250 ˚C max. product.)
❈ In case of applying voltage in alternating current (50 Hz or 60 Hz sine wave) to a capacitor with DC rated voltage, please
refer to the page of “Permissible voltage (R.M.S) in alternating current corresponding to DC rated voltage”.
❈ Please consult us for capacitance range between 0.15 µF and 1.0 µF for 250 VDC type.
Design, Specifications are subject to change without notice. Ask factory for technical specifications before purchase and/or use.
Whenever a doubt about safety arises from this product, please inform us immediately for technical consultation without fail.